Round Type Hydraulic Cylinder (The tightening torque should be about 2 to 3 Nm.) 5. Modification of the detecting position should be made in the condition of 3. 329
Note 2) When exceeding the standard strokes, it will be out of warranty.
Note 2) When exceeding the standard strokes, it will be out of warranty.
A contact protection box should be used in any of the above situations. The life of the contacts may otherwise be reduced. (They may stay on continuously.)
* 9 : 025 --l ,eln the machjne lype seleclion whn I dimsnsion becoms longer, selct the cylinclr hsvins a suflicient i. 020 \ Not t) when the cylinder i to be used ae a stopper use is at 30 stroke or les. Note 2) MGOL (Ball bush bea/ng) cannot be used as C16 012 \ \ '**;;.
* 9 : 025 --l ,eln the machjne lype seleclion whn I dimsnsion becoms longer, selct the cylinclr hsvins a suflicient i. 020 \ Not t) when the cylinder i to be used ae a stopper use is at 30 stroke or les. Note 2) MGOL (Ball bush bea/ng) cannot be used as C16 012 \ \ '**;;.
Type: 000 (Lever Type Feedback), Pressure Gauge: 3 (1.0MPa), Construction: 1 (w/Terminal Box), Accessories: BE (B+E), Connection: 1 (1/4NPT, G1/2)
Type: Lever Type Feedback, Pressure Gauge: 1.0MPa, Construction: w/Terminal Box, Accessories: B+E, Connection: 1/4NPT, G1/2
Water Precautions Be sure to read before handling.
In the case of characteristic a, time delav to switch a valve with switching pressure ps will be lt, b it will be increased lo t2.
In the case of characteristic a, time delav to switch a valve with switching pressure ps will be lt, b it will be increased lo t2.
When mounting a band on bore size 8, 10, or 12, the D-A9l(V) cannot be mounted. When mounting a rail on bore size 8, 10, or 12, the D-A9l(V) and A79W cannot be mounted.
A short circuit breaker or fuse should be installed. 4. When a valve is to be heated, only the body section should be heated, excluding the bonnet section. 5. When a heater is in operation, the entire valve becomes hot. Be careful not to touch it with bare hands, as burns will result. Piping Caution Selection Caution 1.
Grease should be applied at 1 million cycles or 200 km, whichever comes first. LEC Y Motorless Motorless Grease pack order number: GR-S-010 (10 g)/GR-S-020 (20 g) LAT LZ LC3F2 885
Do not use in a place where the product could be splashed by oil or chemicals. If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction etc.). Do not use the product in an environment where corrosive gases or fluids could be splashed.
Symbol of position for port and cushion valve has to be looked from the rod side, as figures above. (In the case of standard cylinders, port must be positioned in the upper side.) Define the upper side to be A, and then B, C, and D in a clockwise order. 2.
Extended periods of continuous energization Contact SMC if valves will be continuously energized for extended periods of time. Caution 1. Momentary energization If a double solenoid valve will be operated with momentary energization, it should be energized for at least 0.1 second. 2.
Dedicated grounding should be used. Grounding should be to a D-class ground. (Ground resistance of 100 or less.) 3. Grounding should be performed near the actuator to shorten the grounding distance. -14- 4. The cross-sectional area of this wire shall be a minimum of 2 mm2. 5. Avoid common grounding with other devices.
(Reference tightening rotation angle: approx. 1/4 to 1/2 turn after tightening by hand) This makes the element e be pushed up as a whole, and the element seal will be installed to the case q sealing. The element e can also be pushed hard by hand to be surely installed before setting the case q. 2-4.