CV/MVGQ (If used with gataway unit, SI must be output only.)
Even within a given allowable kinetic energy level, there is an upper limit to the size of the load that can be sustained. Thus, a horizontally mounted cylinder must be operated below the solid line, and a vertically mounted cylinder must be operated below the dotted line.
Note) It may be difficult to replace the cushion seal #8. Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g) Piston seal NBR Scraper NBR Cushion seal NBR 167
Give us a call today and discover just how amazing SMC Serial Network system can be.
Use a 3 wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be "n" times larger when "n" auto switches are connected in parallel.
In cases where the management of drain flushing will be difficult, the use of fillers with automatic drains is recommended. The product should be mounted and operated with a good understanding of its contents. Also, keep the manual where it can be easily referred to at any tIme.
Be certain that the secured portions will not loosen. Be certain to adopt a reliable connecting method if the cylinder is used very frequently or if it is used in a location that is exposed to a large amount of vibration. There may be cases in which a speed reduction circuit or a shock absorber is required.
When In the exhaust posiiion, the vahre may be padlock secured. Prevents accidental start-ups whil personnl ate cleanlng or serviclng equipment. operated valve can be used to The supply/exhaust status of the air flo$r can be verified al a glance in the indicating windour.
(If mixed with other grease, optimum performance cannot be achieved.) 4-1. Food Machinery Grease Specification Standard models -XC85 Grease pack part number: GR-H-010(10g) Nonfood compound incidental contact. Operating Environment Caution Environment for installing cylinder Do not use in food zone. 4-2.
When a speed controller is mounted, the cylinder installation area can be reduced significantly. The dust seal band can be removed by loosening two holding screws (on one side).
I/O above 128 cannot be recognized.)
If the initial pressure drop is set to be high, its service life will be shorten due to clogging. 2) TSJ connection The TSJ fitting is a kind of a self-align fittings. Set it as shown in the figure.
The grease to be applied is available as grease pack. When the grease pack is required, order it using the part number shown below. Grease pack part number: GR-S-010 (10g) ( The grease to be applied is the same as that used for the cylinder.) Lock pin Built-in shock absorber Piston rod Similarly, be careful not to remove the grease from the piston rod end of the built-in shock absorber.
(If used with gataway unit, SI must be output only.)
Note 2) On the AMC220, an R 1/4 fittinng can be attached by removing the drain cock. (It be comes the drain piping type.
Grease pack part number: GR-S-010 (compatible with all sizes) Note 2) Cylinders with 50 or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassemble is required.
Note 3) The sensor for the external sensor type is not attached and must be ordered separately. Any pressure sensor that transmits analog output signals can be connected.
Each rotation angle end can be adjusted 5. When the cylinder is pressurized from port B, range E can be adjusted by regulating angle adjustment screw C. When the cylinder is pressurized from port A, range F can be adjusted by regulating angle adjustment screw D.
CLKU cannot be disassembled and therefore no seal kit is available. LGrease Pack Kit no. Contents Rod seal GR-S-010 Grease 10 g Please consult with SMC when replacing the actuating cylinders. Piston seal LShim (Option) Refer to page 543 for details about part numbers and dimensions. Bumper CKU32-120RL-X2321 LGuide Pin Order No. LClamp Arm Assembly Order No.