5 Port Solenoid Valve Series SV1000/2000/3000/4000 AS-Interface (4in/4out 31Slave Mode 2 power supply systems ) AS-Interface (8in/8out 31Slave Mode 1 power supply systems) AS-Interface (4in/4out 31Slave Mode 1 power supply systems) CANopen ControlNet (IP40) EtherNet/IP Input blocks cannot be mounted without SI unit. When the DIN rail is included without an SI unit, the DIN rail length will accommodate an SI unit and one input block.
Cylinder Dead Weight Deflection Series CY3B is guided by an external axis (such as a linear guide) without directly mounting the load.
Seal Kit List (12, 13, 18 and 20 are not included in the seal kit. Order them as required with by individual part numbers.) Description Qty.
mA D side EVS Note 1) Combining valve VFR31 (single) and release valve spacer makes it possible to use this as an air release valve.
Power supply cable (LEC-CK1-1) is an accessory.
switch (Lm) Operating angle m: The value of the individual switchs movement range Lm as represented by an angle.
Do not use in an environment with temperature cycles. Consult SMC if switches are used where there are temperature cycles other than normal temperature changes, as they may be adversely affected. 6. Do not use in an environment where there is excessive impact shock.
As the high-pressure liquid refrigerant passes through a constricting mechanism, such as an expansion valve, it rapidly depressurizes and some of the refrigerant evaporates. The release of evaporation heat causes the refrigerant itself to cool so that it becomes a combination of gas and liquid at a lowExpansion valve A component that creates an expansion in the refrigeration circuit.
(For the ball screw drive) 2 Consult with SMC for non-standard strokes as they are produced as special orders. 3 For clean room specification, refer to pages 20 and 92.
Bore size 40 mm (1-1/2) 50 mm (2) 63 mm (2-1/2) Stroke Hundredths of an inch* 20 25 32 40 50 63 20 mm (3/4) 25 mm (1) 32 mm (1-1/4) Stroke length must be indicated as 4 digits.
The combination as standard is as follows. Part no.
Since no protective cover is installed on the product, provide an external protective cover protecting the entire product wherever possible. Using the product in an environment where it is exposed to water, liquid coolant or dust such as iron powder will cause an adverse effect to the ball screw and the guide. Therefore, an external cover is also required for dust prevention. 8.
gravity [mm] Model LEJS40 LEJS63 LEJB40 LEJB63 5000 mm/s2 or less is same as 5000 mm/s2 5000 mm/s2 or less is same as 5000 mm/s2 5000 mm/s2 or less is same as 5000 mm/s2 5000 mm/s2 or less is same as 5000 mm/s2 2000 2000 1000 1000 L7 800 800 1500 1500 L7 [mm] L7 [mm] L7 [mm] L7 [mm] 600 600 1000 1000 m Me X 400 400 500 500 200 200 0 0 0 0 0 10 5 15 20 0 10 5 15 20 30 25 0 10 40 50 20 30 0
An external pilot style that can be used individually is available as a made-to-order. For details, refer to the page 4-6-46.
Mixed single and double wiring is available as an option.
OPTION S SERIES 70 OPTION AS OPTION Q SERIES 20 & 30 SERIES 20 & 30 SERIES 70 OPTION AD OPTION AS OPTION AD AN CONNECTOR AUTOMOTIVE TERMINAL SINGLE STRAIN RELIEF CONNECTOR SUPPLIED WITH SJT LEADS AUTOMOTIVE TERMINAL SINGLE AUTOMOTIVE TERMINAL DOUBLE AUTOMOTIVE TERMINAL DOUBLE OPTION J J.I.C. HOUSING (SERIES 20 ONLY) When additional solenoid protection is required, Peter Pauls J.I.C.
When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit, etc. 9. When an impact, such as water hammer, etc., caused by the rapid pressure fluctuation is applied, the solenoid valve may be damaged.
15, 20, and 30 are the same as those of single type.
OPTION S SERIES 70 OPTION AS OPTION Q SERIES 20 & 30 SERIES 20 & 30 SERIES 70 OPTION AD OPTION AS OPTION AD AN CONNECTOR AUTOMOTIVE TERMINAL SINGLE STRAIN RELIEF CONNECTOR SUPPLIED WITH SJT LEADS AUTOMOTIVE TERMINAL SINGLE AUTOMOTIVE TERMINAL DOUBLE AUTOMOTIVE TERMINAL DOUBLE OPTION J J.I.C. HOUSING (SERIES 20 ONLY) When additional solenoid protection is required, Coast's J.I.C.
Remove the covers as shown in Figure (2) and make further adjustment by loosening the hexagon nut. 3. Various dimensions are indicated in Table (1). Never make an adjustment that exceeds the dimensions in the table, as it may cause an accident and/or damage.