Cylinder with Lock Series CLS When in a locked condition, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of overrun when an intermediate stop is performed.
Note 2) Even without an SI unit, the length of the DIN rail can accommodate an SI unit. If a shorter length for the DIN rail is desired (same as type 45), add "0" for option at the end of the part number. SS5Y3-45S1BD-05U-C6-Q.1 set (Type 45S1, 5 station manifold base with serial unit part no.) SY3140-5FU-Q . 3 sets (Single solenoid part no.)
For male thread When in the locked state, do not apply a load accompanied by an impact shock, strong vibration, turning force, etc. 30 Note that an external action, such as an impacting load, strong vibration, or turning force, may damage the lock unit or reduce its life.
When ordering nuts as spare parts, size 4 and 5 are as shown below.
As a result, the inside of the bowl q is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl q, it will not drain out.
As a rule, turn the screw an additional 90 after tightening resistance is felt. FB 50 Stroke 66 67.5 109 109 117.5 117.5 121 141 51 Stroke or more 97.5 99 114 114 129 129 148 166 20 25 32 40 50 63 80 100 66 67.5 71.5 78 83 88 102.5 120 19 20 22 22 23 23 24 29 * Other dimensions are same as standard.
Nil (Rear piping) L (Bottom piping) Bracket A A1 ZS-46-A1 Bracket C A3 ZS-46-E B ZS-46-B Panel mount adapter E ZS-35-B D ZS-46-D Panel mount adapter + Front protective cover F ZS-35-E -9No.PS-OMU0009-D Accessories/Part numbers If an option is required independently, order with the following part numbers. Items Part No.
When designing an application, be sure to allow sufficient clearance for maintenance and inspections. x 1000 Auto switch operating range (mm) V(mm/s) = Time load applied (ms) In cases of high piston speed, the use of an auto switch (D-F5NT) with a built-in OFF delay timer (approx. 200ms) makes it possible to extend the load operating time. 4. Wiring should be kept as short as possible.
Also, applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.
adjustment is required as shown in the chart below).
Use self-align fittings in the piping for an air-hydro cylinder. Do not use One-touch fittings in the piping for an air-hydro cylinder, as oil leakage may occur. 2. Use tubing materials such as hard nylon or copper for air-hydro cylinder piping.
The Number of Insertions and Removals from Self-seal Fitting Caution qThe number of insertions and removals as a rough quide is as follows.
Do not install the product in an environment under the devices. It may cause an electric shock or damage to the driver. effect of vibrations and impacts. It will cause failure or malfunction. 2. Do not perform the operation or setting of the product 17. When a surge generating load such as a relay or solewith wet hands.
Use a flexible material for piping (such as a rubber hose) and an accumulator that can absorb impact pressure. 3. Keep piping as short as possible. Use the product within the specified operating pressure and temperature range. Reserve a space for maintenance.
Applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.
As a result, the inside of the bowl q is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl q, it will not drain out.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
An over current error (Er1, Er2) is displayed. (1) Check that there is no noise interference such as static electricity, and check for noise sources.
Nil (Rear piping) L (Bottom piping) Bracket A A1 ZS-46-A1 Bracket C A3 ZS-46-E B ZS-46-B Panel mount adapter E ZS-35-B D ZS-46-D Panel mount adapter + Front protective cover F ZS-35-E -9No.PS-OMX0002-A Accessories/Part numbers If an option is required independently, order with the following part numbers. Items Part No.