HRX-OM-X084 D.IN1 SEL No.7 screen Contact input signal 1 type ALT ALT/MT D.IN1 SW TYPE No.8 screen Contact input signal 1 operation A A/B D.IN1 CON TYPE No.9 screen Contact input signal 2 function OFF OFF/STOP/SW D.IN2 SEL No.10 screen Contact input signal 2 type ALT ALT/MT D.IN2 SW TYPE No.11 screen Contact input signal 2 operation A A/B D.IN2 CON TYPE No.12 screen Contact output signal 1
OUT mon 1 HOLD [ ] SVON [ ] OFF DRIVE [ ] ON [] [ ] (6-3-3-2) Input I/O HOLD keykey SVON I/O DRIVE RESET SETUP JOGJOG+ FLGTH MODE WRST Brake SW Origin SW SW-FF Limit SW-F SW-RR Limit SW-R EMS B Enable SW EMS EMS EMS 82 - (6-3-4) (6-3-4-1) Output pinSET AX IS. Monitor 1 Output Input Output pin SET AX IS.
4 A 4 A 4 A 4 A 4 A 4 A 4 A 33.5 11.5 15.7 12 2-Rc 1/8 (Pilot exhaust port) VQ5 (6.5) 21.5 2-Rc 1/8 (External pilot port) 27 2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port> Rc 1/4: 1/4" Female thread Rc 3/8: 3/8" Female thread C8 : 8 One-touch fitting C10 : 10 One-touch fitting C12 : 12 One-touch fitting 31 VQZ 38.7 VQD Manual override Indicator light L2 L1 79.5 6.5 P=25 65.5 72 R4.5 46 Mounting
Normal output Reversed output P_1(P_2)=A-(A-B)/4 n_1(n_2)=B+(A-B)/4 A = Maximum pressure H_1(H_2)= (A-B)/2 H_1(H_2)= (A-B)/2 B = Minimum pressure If setting is not necessary press the UP and DOWN buttons simultaneously for 1 second or longer. -37No.PS-OMY0007-A [F 6] Fine adjustment of display value This function is to manually perform a fine adjustment of the displayed pressure value.
Normal output Reversed output P_1(P_2)=A-(A-B)/4 n_1(n_2)=B+(A-B)/4 A = Maximum pressure H_1(H_2)= (A-B)/2 H_1(H_2)= (A-B)/2 B = Minimum pressure If setting is not necessary press the UP and DOWN buttons simultaneously for 1 second or longer. -36No.PS-OMV0004-H [F 6] Fine adjustment of display value This function is to manually perform a fine adjustment of the displayed pressure value.
A-q A-w A-e A-r A-t A-y A-u A-!1 A-y A-u A-!2 A-!
CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution : WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning : DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
A-q A-w A-e A-r A-t A-y A-u A-!1 A-y A-u A-!2 A-!
B-1 2 (L) A A-1 1 B B-2 6 1 1.5m B A-2 5 COM-A/COM B-3 3 3 3m COM-B/ A-3 4 5 5m Shield (3) Vcc B-4 12 GND A-4 13 A B-5 7 A A-5 6 B B-6 S 9 B A-6 8 3 (14.2) (2) 2 1 (8) (1) B1 A1 (14) (18) (17.7) 5 6 (3) 2 1 A6 B6 15 16 L (11) (30.7) 14.2 [820m] LE-CP(1) (2) * * A B-1 2 (L) A A-1 1 B B-2 6 8 8m * B A-2 5 COM-A/COM B-3 3 A 10m * COM-B/ A-3 4 B 15m * (3) Shield
(A-B)/4 n_1(n_2)=B+(A-B)/4 A= H_1(H_2)=(A-B)/2 H_1(H_2)=(A-B)/2 B= UPDOWN1 -36No.PS-OMV0003CN-G [F 6] 5R.D. <> UPDOWN[F 6] SET UP DOWN SET [F 6] -37No.PS-OMV0003CN-G [F10] 39 <> UPDOWN[F10] SET UP DOWN 2 OFF (OUT1) (OUT2) [dUAL]2 SET () [LinE] SET () () 40 () UP DOWN () SET , (SET ) SET () [dUAL]2 SET () AbY(Z) 40 () 019 ( ) UP DOWN / () SET 1 () SET SET [F10
Drawing shows a SC case. (general purpose type) Dust-protected SI unit (L4) (L3) L2 (5.25) (12) 13 27 28 L1 Indicator light 63.5 10.5 (n-1) x 10.5 23.5 1.5 Manual override B A B A B A B A A A A FG + + 0V 24V SMC S E R I A L U N I T MODEL SC (SI No.EX120-STA1) 2 93.5 66 64 ERR T/R RUN (35) (5.5) 0 1 DIP SW. 4 x M4 mounting hole 61.5 4.5 Drawing shows a SC case.
Tightening torque for terminal: 0.6 Nm Series VFS4000/5000 Model Terminal block marking A + A side A side A A side A side B + B VFS 100 VFS 200 VFS4 00 VFS5 00 4 5 4 5 B side B side 3 4 3 4 A side A side B side B side Applicable terminal: 1.25-3.5M, 1.25Y-3L, 1.25Y-3M There is no polarity.
Normal output Reversed output P_1(P_2)=A-(A-B)/4 n_1(n_2)=B+(A-B)/4 A = Maximum pressure H_1(H_2)= (A-B)/2 H_1(H_2)= (A-B)/2 B = Minimum pressure If setting is not necessary press the and buttons simultaneously for 1 second or longer. -37No.PS-OMU0012-C [F 6] Fine adjustment of display value This function is to manually perform a fine adjustment of the displayed pressure value.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
RJ45 8P LEC-CG1LEC-CG1a) RJ45 8P a) RJ45 8P No 1 LEC-CG1CN1 K 0.3m (LEC)CN4 L 0.5m 1 1m 2 LEC-CGD (LEC) 3 LEC-CG2K 0.3m L 0.5m 1 1m 4 M1 4 XS2C-D4 [] 120 1/4W 5 RJ-45 CN1 CN2 RJ-45 LEC-CAP-X22 27 - No a) RJ45 8P TM21P-88P HIROSE b) M12 4pin HR24-8DJ4PE550A(73) HIROSE XS2G-D4 [] c) M12 4pin HR24-8DP4S300(73) HIROSE XS2C-D4 [] 28 - 82 CN1 CN1 (LEC) 120 1/4W OV CN1
stop (e.g. a large load is mounted on a carrier). 7 11 7.
Refer to 7.2 Setting parameters for details. 46 No. JXC-OMU0029-A 8.5 Servo ON Servo ON signal is not assigned to the parallel I/O of this controller. The power supply LED (a) changes from a flashing light to a solid light after a specific period of time after power supply and the servo turns on.