REA/REB The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
C6 (EXH) port One-touch fitting for 6 EXH passage blocked Note) R block valve is mounted in the blocking position when ordering an individual EXH spacer incorporated with a manifold. When separately ordering an individual EXH spacer, separately order a R block valve.
hole DIN terminal Conduit terminal S Q F Cable 6 to 12 Q2 S2 F D G1/2 (44) 31.5 32 25 Y T R E C R C G1/2 (1.5) (1.5) Y E B1 B A A B1 B 2 x P Port size 2 x P Port size U W M U W M 2 x 5.3 Mounting hole X 2 x 5.3 Mounting hole X (mm) Mounting bracket dimensions Port size P Size A B B1 C D E F M 12.8 19 19 U 46 56 56 W 36 46 46 X 11 13 13 Y 6 7 7 1 2 19 24 24 30 43 45 45 50 21 22.5 22.5
-46-> A set of thread adapters that converts the connections from Rc to NPT is enclosed as an accessory.
It may cause human injury and/or an accident. 14. Refer to the Auto Switches Precautions for using with an auto switch. 15. When a cylinder is used in a clamping, suspending and lifting mechanism There is a danger of workpieces dropping if there is a decrease of thrust due to a drop in circuit pressure caused by a power outage, etc.
When it is necessary to operate it as an ordinary double acting cylinder at an even lower operating speeds, use a low speed cylinder (refer to Made to Order on page 6-17-19).
Note Bracket A ZS-46-A1 For rear ported/Tapping screw: Nominal size 3 x 8 L (2 pcs.)
Note 2) Changing from an internal pilot to an external pilot or vice versa is not possible. 04 4 5 1 VP3 A G 1 04 4 5 1 VP3 A G 1 Pilot option VP 3 port solenoid valve Standard (Internal pilot) External pilot 1 Nil 1 Type of actuation 1 No. of solenoids Single A B N.C. (Normally closed) N.O.
Install a diode (D) for an inductive load, or install an inrush current suppressing resistor (R) for a lamp load. (Rated current: 40 mA or less, maximum current: 50 mA or less, inrush current: 100 mA or less) A maximum of 5.2 V voltage drop occurs in the driver.
When disassembling a cylinder with a bore of 20 to 40, use a vise or the like to hold the wrench flats portion of the tube cover or the rod cover on one side, while placing a wrench or an adjustable wrench on the other side to loosen and remove the cover. To replace, tighten it an additional 2 from the installed position.
29 11 11 5.1 5.1 9.5 9.5 B H A 26 10.5 26 10.5 (NN 1) x H G Section AA Section BB (mm) Model F 45 40 48 58 42 55 50 55 62 N 4 4 4 4 6 6 8 8 8 G 22 22 22 22 17 18 37 56 H 46 46 46 56 56 56 59 62 NN 2 2 2 2 3 3 4 4 4 GA 18 18 18 22 48 73 74 96 118 HA 50 50 50 56 48 56 112 118 124 I 16 16 16 16 18 23 25 18 21 J 46 46 46 56 72 100 155 190 215 K 31 41 51 61 71 96 121 146 171 KA 126 183 211
29 11 11 5.1 5.1 9.5 9.5 B H A 26 10.5 26 10.5 G (NN 1) x H Section AA Section BB (mm) ZZ 108 108 108 118 136 169 226 254 282 M 94 94 94 104 122 155 212 240 268 Z 92.5 92.5 92.5 102.5 120.5 153.5 210.5 238.5 266.5 K 31 41 51 61 71 96 121 146 171 J 46 46 46 56 72 100 155 190 215 I 16 16 16 16 18 23 25 18 21 NN 2 2 2 2 3 3 4 4 4 H 46 46 46 56 56 56 59 62 G 22 22 22 22 17 18 37 56 N 4 4 4
This product cannot be used as a check regulator by installing it between solenoid valve and actuator. 3. Port with a pressure gauge or a plug can be used as an OUT port.
Approx. 5.6k Approx. 5mA Switch TR DICOM VCES 1.0V ICEO 100 A 24VDC 10% 200mA (2) Digital output interface DO-1 A lamp, relay or photocoupler can be driven. Install a diode (D) for an inductive load, or install an inrush current suppressing resistor (R) for a lamp load.
How to Order Type 46 (5 port / Base mounted) Applicable solenoid valve 10-SYJ34310--SS5YJ3-46-05 -M5 Type 46 Type S46 Applicable blanking plate assembly SYJ3000-21-2A ( ) Single solenoid coil is located on the same side of A and B ports.
Lock monitor (A) details An offset load can be operated if there is an effective guide to absorb all of the generated moment.
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. wUse a balance circuit in which lurching of the piston is taken into consideration.
A A A A A Note) For details of the applicable tubing sizes, refer to page 945.
Once that position is reached, rotate it for an additional 1/6th of a turn to securely tighten the lock release bolt. * Do not use an electric screwdriver or pneumatic screwdriver.
Remarks Bracket A ZS-46-A1 Self tapping screws: Nominal size 3 x 8L (2 pcs.) Bracket B ZS-46-A2 Self tapping screws: Nominal size 3 x 8L (2 pcs.)