Mechanically Jointed Rodless Cylinder Series MY1 In such a case, use a side support in the middle section. The spacing (l) of the support must be no more than the values shown in the graph on the right. W kg 500 l 400 Mass m (450) W l Caution 300 W 1. If the cylinder mounting surfaces are not measured accurately, using a side support may cause poor operation. Therefore, be sure to level the cylinder tube when mounting.
D-A90V, D-A93V, D-A96V Note) A contact protection box should be used in any of the following conditions to prevent the shortening of the working life of the switch.
Minimum operating voltage of load Supply voltage > Internal voltage drop of switch 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator light (D-A90, D-A90V, D-Z80).
D-A90V/D-A93V/D-A96V Note) q In a case where the operation load is an inductive load. w In a case where the wiring load is greater than 5 m. e In a case where the load voltage is 100 VAC. Please use the auto switch with a contact protection box any of the above mentioned cases. (For details about the contact protection box, refer to page 17.)
Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.
(lbs) Weight (Except Non-rotating Rod) Bore size (inch) Base weight by mounting style Addl weight per inch stroke Addl weight for magnet Addl weight for bumper B 0.059 0.080 0.200 0.218 0.330 0.531 0.680 1.345 C 0.076 0.091 0.200 0.198 0.320 0.581 0.710 N/A E 0.076 0.091 0.280 0.288 0.410 0.681 0.820 1.493 R N/A N/A 0.210 N/A 0.430 N/A 1.020 N/A W N/A N/A 0.300 0.308 0.400 0.781 0.930 1.812
The maximum dimension L2 is, as a rule, twice the thread size. (Example) For M4: L2 = 8 Applicable shaft types: S, W Machine female threads into the long shaft. The maximum dimension L1 is, as a rule, twice the thread size (Example) For M3: L1 = 6 Applicable shaft types: S, W 1. Enter the dimensions within a range that allows for additional machining. 2.
A C B A C B A stroke operation 1) Initial state (0 stroke position) W W A stroke B stroke A stroke 2) Operation When the air pressure is supplied from the A port, the rod operates the A stroke. A Precautions C B A stroke Caution 1. Do not supply air until the cylinder is fixed with the attached bolt. 2.
A for detailed dimensions, specifications and lead times.
As a rule when W + Pa>PA adjust P so that W + Pa = PA. (2) Installing a regulator with check valve at position (b) can decrease lurching during descent and actuation delay during ascent. As a rule adjust P so that W + PA = Pa.
24.5) Indicator light Slotted set screw M2.5 x 4 l DC (+) Brown LED diode D-A90 type comes without indicator light. (+) Resistor Load Reed switch DC power supply OUT Black Reverse current prevention diode Most sensitive position 10 ( ): D-A93 D-A90V/D-A93V/D-A96V () DC () Blue Note) q In a case where the operation load is an inductive load. w In a case where the wiring length is greater than
When using as a stopper, select a model with 30 stroke or less. 2.
Please contact SMC when the AC welding current exceeds 16000 A.
D-F9 7 16 20 42 47 44.5 42.5 49 57 81 84 87.5 Switch Hysteresis D-F9W 6 15 19 41 46 43.5 Proper auto switch mounting positions (Series CEP1 ) (mm) Bore size (mm) 12 Auto switch model Symbol 20 A B A B A B A B A B A B A B 75.2 82 Switch operating position (ON) D-A90, A93, A96 7.9 12 75.2 82 D-A90V, A93V, A96V 7.9 12 Hysteresis Reed switch: 2mm or less Solid state switch: 1mm or less 79.2 86
Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator for right (MODEL D-A6/A80/A80H/A90/A90V/C80/R80/90/E80A/ Z80)
Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator for right (MODEL D-A6/A80/A80H/A90/A90V/C80/R80/90/E80A/ Z80)
Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator for right (MODEL D-A6/A80/A80H/A90/A90V/C80/R80/90/E80A/ Z80)
Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator for right (MODEL D-A6/A80/A80H/A90/A90V/C80/R80/90/E80A/ Z80)
Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator for right (MODEL D-A6/A80/A80H/A90/A90V/C80/R80/90/E80A/ Z80)
Supply voltage Internal voltage drop of switch > Minimum operating voltage of load 2) If the internal resistance of a light emitting diode causes a problem, select a switch without an indicator for right (MODEL D-A6/A80/A80H/A90/A90V/C80/R80/90/E80A/ Z80)