PF3A7xxH.eng Function (Main display) Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system. System error (2) Press the or button to change the set value. The button is to increase and the button is to decrease the set value.
CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Sub display Displays the accumulated flow, set value and peak/bottom value when in measurement mode. 2 1 (5) Press and hold the S button for 2 seconds or longer to complete the simple setting.
[F 2] Setting of OUT2 Same setting as [F 1] OUT1. The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Press the SET button for 2 second or longer.
in a location where it will be used as a support.
Internal circuit and wiring example Setting of NPN open collector 2 outputs: Pressure sensor 3-wire type Mounting hole Screws are mounted to the holes for installation. (Equivalent to M4) CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Description F80 F10 [LEvEL] Level meter [ ON] Normal operation 2 1 DC(+) 2 To obtain the operation manual about this product and control unit, please refer to the SMC website (URL http://www.smcworld.com) or contact SMC directly.
Circuit (of class 2) which is of maximum 30 Vrms (42.4 V peak), with UL 1310 class 2 power supply unit or UL 1585 class 2 transformer. The product is a approved product only if it has a mark on the body.
Operation LED Danger: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. (4) Press and hold the S button for 2 seconds or longer to complete the OUT setting. (If the button is pressed for less than 2 seconds, the setting will be returned to P.)
[F96] Number of pressurizing errors std (Standard) [F10] Sub display setting CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: N/A (normal output) [F98] Output check 1000-split [F11] Display resolution setting Orifice [Simple setting mode] Select the set value, hysteresis and delay time.
The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body.
The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Turn the power off and on again.
The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body.
PNP open collector 2 output + Analogue output Max. 80 mA Residual voltage: 1.5 V or less Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
The direct current power supply to be used should be UL approved as follows: Circuit (of Class 2) which is of maximum 30 Vrms (42.4 V peak), with UL1310 Class 2 power supply unit or UL1585 Class 2 transformer. The product is a UL approved product only if it has a mark on the body. Turn the power off and on again.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the pressure switch body with a spanner. longer simultaneously, the main display shows [-], and the reset to zero.
Atmospheric vent port Used to mount the product on a DIN rail. DIN rail mount CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the Z/ISE20 body with a spanner. Pressure second or longer simultaneously.
[F 2] Setting of OUT2 Same setting as [F 1] OUT1. Item Default setting OUT2 set value Bottom value Peak value OUT2 hysteresis Mounting with panel mount adapter
The initial value is " A: A contact (normally open)(output 1,3) / B: B contact (normally closed) (output 2)".
With functions narrowed down, 2 independent temperature control systems have been achieved with only a single compressor , a single pump , and a single tank .