ELECTRO-PNEUMATIC POSITIONER Pilot unit No. having the Throttle shown at left 90cm3 0.7 P36801080 P565010-18 180cm3 1 P36801081 P565010-19 Fig. 19 Throttle mounting Fig. 20 Pilot valve bottom drawing Throttling diameter OUT2 OUT1 O-ring P5 Throttle (Note 1) When mounting the throttle, pay attention not to let dust and others enter the port hole. Be sure to mount an O-ring after mounting the throttle.
Dimensions Unit: mm Model A B C D E Fn Fd G H J K XLD-25 50 123 48 1 12 40 26 41 16 7.5 XLD-40 65 170 66 2 11 55 41 63 20 15 XLD-50 70 183 79 2 11 75 52 68 20 17.5 XLD-63 88 217 100 3 11 87 95 70 72 20 20 XLD-80 90 256 117 3 11 114 110 83 98 20 26.5 XLD-100 108 321 154 3 11 134 130 102 133 20 38 XLD-160 138 335 200 3 11 190 180 153 114 30 40 11 XL*-OMI0011-E 7.
(Data can be rewritten for up to one million times, and data will be stored for up to 20 years.) 2. The accumulated flow rate is reset when power is turned off. Operating Environment Warning Mounting Warning 1. Never use in the presence of explosive gases. The switches do not have an explosion proof rating.
Example) Assume circuit C with an operating pressure of 0.5 MPa, load weight of 10 kg, fluctuation to 20 kg and a cylinder bore of 32 mm.
Performance Performance data given in this chapter is based on an electrified plate (dimensions: 150 x 150 mm, electrostatic capacity: 20 pF) defined by ANSI standard (ANSI/ESD STM3.1-2006).
The proper tightening torque for screws 0.3 to 0.4 Nm Rated voltage With indicator light VZ Voltage symbol Part no. 24 VDC 12 VDC 100 VAC 200 VAC 110 VAC 220 VAC 24V 12V 100V 200V 110V 220V AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 VS (b) VFN Valve Mounting Circuit with Indicator Light After confirming the gasket is correctly placed under the
Never use in an atmosphere of explosive gases. The structure of switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Mount switches in locations without vibration (98m/s or less) or impact (490m/s or less). 3. Do not use in an area where surges are generated.
(Writing time: 10,000 times, Data duration: 20 years after power off) Use the clean air. This can cause operating failure. If compressed air containing condensate is used, install an air dryer or drain catch before the filter and perform drainage regularly.
Endurance Test An ozonizer was used in a pneumatic circuit to prepare air to an ozone concentration of 1ppm. The test specimens (system components made from HNBR and NBR) were operated using this ozoneladen compressed air, and the endurance of each type of component/material was measured and compared.
Tightening of M3 and M5 screws 1) After tightening by hand, the barb elbow type (M-3ALU-2, M5ALHU-2) should be tighten an additional 1/3 rotations using an appropriate wrench. 2) After tightening by hand, other types should be tightened by an additional 1/6 rotations using a suitable tool.
MY2 H/HT MY3A MY3B MY3M Load Mass Allowable Moment MY1H/m3 MY1H/M3 MY1H/M1 MY1H/M2 q r w e t 30 40 50 50 40 30 40 50 30 40 50 30 20 20 20 20 MY1H40 MY1H32 10 10 10 MY1H40 MY1H40 MY1H32 Load mass kg MY1H32 Moment Nm Moment Nm Moment Nm 5 4 3 MY1H25 MY1H40 10 5 4 3 5 4 3 MY1H32 MY1H25 MY1H25 2 MY1H25 5 4 2 2 1 3 1 1 0.5 0.4 0.3 2 0.5 0.4 0.3 0.5 0.4 0.3 D0.2 1 0.2 0.2 0.1 -X 100 200 300 400
D-A9 30 Note 1) 15 5 (n = 2, 3, 4, 5) (n = 2, 4, 6) Note 3) (n 2) 2 35 + 35 (n 2) 20 + 35 D-M9V 35 20 5 (n = 2, 3, 4, 5) (n = 2, 4, 6) Note 3) (n 2) 2 25 + 35 (n 2) 15 + 35 D-A9V 25 15 5 (n = 2, 3, 4, 5) (n = 2, 4, 6) Note 3) (n 2) 2 D-M9WV D-M9AV 35 + 35 (n 2) 20 + 35 35 20 10 (n = 2, 3, 4, 5) (n = 2, 4, 6) Note 3) (n 2) 2 D-C7 D-C80 60 + 45 (n 2) 20 + 45 60 20 5 (n = 2, 3, 4, 5
20 20 21 H M4 x 0.7 M5 x 0.8 M6 x 1 M8 x 1.25 MM 113 113 115 145 ZZ Bore size 8 8 12 13 Female thread MM 20 25 32 40 Thread depth A1 When female thread is used, use a thin wrench when tightening the piston rod.
Action D Double acting Cylinder stroke (mm) Bore size (mm) Standard stroke (mm) Mounting style Bore size 10 10, 20, 30, 40 Through-hole/Both ends tapped common (Standard) Foot style Rod side flange style Head side flange style Double clevis style B L F G D Note) 10 16 20 25 28 10 mm 16 mm 20 mm 25 mm 28 mm 16 10, 20, 30, 40, 50, 60 20 10, 20, 30, 40, 50, 60 25 10, 20, 30, 40, 50, 75, 100
style Double clevis style B L F G D Note) 10 16 20 25 28 10 mm 16 mm 20 mm 25 mm 28 mm 16 10, 20, 30, 40, 50, 60 20 10, 20, 30, 40, 50, 60 25 10, 20, 30, 40, 50, 75, 100 28 10, 20, 30, 40, 50, 75, 100 Note) Available only for MQQL.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.
Keep this manual in an accessible location.
20 0.5 0.4 0.3 0.2 0.5 0.4 0.3 0.2 25 20 16 16 12 12 0.1 0.1 0 40 60 80 100 120 140 160 180 200 20 20 0 40 60 80 100 120 140 160 180 200 Overhang L (mm) Overhang L (mm) Graph (20) Stroke: Up to 150 stroke Graph (16) Stroke: Up to 150 stroke 10 20 10 20 2 3 4 5 2 3 4 5 Weight W (kg) Weight W (kg) 40 40 32 32 1 1 0.5 0.4 0.3 0.2 0.5 0.4 0.3 0.2 25 25 20 20 0.1 0 40 60 80 100 120 140 160 180
Nil Rod end female thread (Standard) Bore size M Rod end male thread 20 25 32 40 50 63 80 100 20 mm Cylinder stroke (mm) Refer to Standard Stroke on page 775. 25 mm 32 mm Thread type 40 mm Built-in Magnet Cylinder Model 20, 25 50 mm M thread Nil If a built-in magnet cylinder without an auto switch is required, there is no need to enter the symbol for the auto switch.
14 32 16 13.5 8 42 8 10 46.4 M14 x 1.5 M32 x 2 Long Male Rod End P S ZZ Boss-cut Female Rod End Bore size 20 25 32 40 Bore size (mm) (mm) Bore size (mm) ZZ A1 8 H MM M4 x 0.7 ZZ 88 A 18 AL H 41 ZZ 109 Bore size 20 25 32 40 55 99 M5 x 0.8 20 25 32 40 20 25 32 40 56 103 86 M5 x 0.8 20 15.5 Rc1/8 62 109 90 8 22 20 M5 x 0.8 89 19.5 45 114 Rc1/8 67 125 96 12 22 20 M6 x 1 95 19.5 45 120 109 13