Speed Controller with Uni One-touch Fitting AS Series Push-lock type A ridge shape has been created as a Uni thread for common applications for Rc, G, NPT and NPTF. AS-FM Note) Universal type is not available.
As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.
For a vacuum application, use VHK2 (2 way valve).
For a vacuum application, use VHK2 (2 way valve).
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.
Tightening of M3/M5 Threads 1) Tighten a barb fitting by hand, and give it an additional 1/6 turn with a wrench. 2) Tighten a barb elbow by hand, and give it an additional 1/3 turn with a wrench.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
U B A Approx. U A B D-A7H D-A80H D-F7 D-J79 D-F7W D-J79W D-F7F D-F7NTL D-F7BAL SMC SMC Approx. U Approx. U Approx. U SMC SMC Approx. U A B B A Approx. U D-A73C D-A80C D-J79C B A A B Approx.
Install with out port down in a vertical position. Inclination from the vertical line should be less than 5. 2. Install with at least 200 mm of free space above the unit to allow for maintenance. 3. To place this product near the air compressor, install in such a way that the vibrations will not be transmitted. 4. Install a valve to drain inlet so that maintenance is possible.
9.5 5.1 11 11 5H9 ( ) depth 5 +0.030 0 30 1.5 NN x M6 x 1 thread depth 12 B A 6 Section AA Section BB HA GA 5H9 ( ) depth 5 +0.030 0 (mm) Model F 50 50 50 60 35 60 70 70 80 ZZ 121 121 121 131 146 185 238 292 344 M 83 83 83 93 108 147 200 254 306 Z 81.5 81.5 81.5 91.5 106.5 145.5 198.5 252.5 304.5 K 31 41 51 61 71 96 121 146 171 J 44 44 44 54 69 108 113 155 190 I 10 10 10 10 10 10 58 70 87
Because tube fittings are provided, use a tube with a bore of 10mm, and keep the overall pipe length within 5m. AM850 type (N.O) Use a tube with a bore of 9mm or more, and keep the overall pipe length within 2.8m.
Even if a proper plier (tool for installing a C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a C retaining ring). Be much careful with the popping of a retaining ring.
(If a terminal plug is not used, the GW unit is COM LED will not light up.)
Even if a proper plier (tool for installing a C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a C retaining ring). Be much careful with the popping of a retaining ring.
Table 10-1 specifications EX245-FPS1 EX245-FPS2 EX245-FPS3 (W x L x H) mm 85 x 148.5 x 136 1,100 g 1,200 g 8 128 () 64 (US1) 350 mA 300 mA (US1/US2) XD1/XD2 16 A (US1/US2) 10 A (US1/US2) 24 VDC +20%/-15% <20.4 VDC US1 >21.6 VDC < 17 VDC 6 A 24 VDC +20%/-15% <21.6 VDC : >22.8 VDC US2 / <17 VDC 4 A () 1.2 V US1 US2 4 8 US1 UT1/UT2 24 VDC +20%/-15% 2 A( UT1) 1 A (
Soft Start-up Valve A V2000/3000/4000/5000 New New Series AV5000 introduced!
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be offset, which results in the generation of a lateral load that can cause malfunction.
Because tube fittings are provided, use a tube with a bore of 10mm, and keep the overall pipe length within 5m. AMH850 type (N.O) Use a tube with a bore of 9mm or more, and keep the overall pipe length within 2.8m.
DIN rail mounting adapter is mounted onto a screw mounting type controller afterwards.