CNG

If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

AC Servo Motor Driver (MECHATROLINK-III type)

/SO2+ 23 1 Lock interlock signal 2 Used for general-purpose output. Note: Set the parameter to allocate a function.

CYP

When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

CRQ2

When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

IN20267

Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Do not use this cylinder as a stopper. Minimum adjusting stroke necessary for a positioning stop is 5mm. Operate for 5mm or more before a positioning stop. Ex: 1.

Digital pressure switch for energy-saving control ejector

CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution : WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning : DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

SMC CORPORATION OF JAPAN

This chapter has been formulated to have a description of the Function Block, a diagram of the Function Block as seen on the LCD Display, and a logic table to show how the Output is controlled by the input signals. An Input that is ON (or High) is shown as a 1 while an input that is OFF (or Low) is shown by a 0.

Compact Type

Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.

70pvpump

(A) 2 N.O.

Electric Slide Table / High Precision Type 《 AC servo motor 》

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

LEKF-OMZ0035

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

CQS

For installation and removal, use an appropriate pair of pliers (tool for installing a type C snap ring). 2. Even if a proper plier (tool for installing type C snap ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier (tool for installing a type C snap ring).

MGZ Series

It is again necessary to connect a contact protection box in order to extend its life. Please contact SMC in this case. If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box.

Secondary Batteries

(Normally closed) A N.O.

NCA1

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if the surge is applied repeatedly. When a load, such as a relay or solenoid which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.

Compressed Air Preparation Filter

AD27-6-A With bowl guard AD27-6C-A AD37m-6-A AD47m-6-A Normally open (N.O.) With bowl guard AD38m-6-A AD48m-6-A Automatic (Auto drain) Manual With drain cock C2SF-2-A C3SF-2-A C4SF-2-A With level gauge C3LF-8-A C4LF-8-A With drain guide (without valve function) C2SFm-2J-A C3SFm-2J-A C4SFm-2J-A With level gauge C3LFm-8J-A C4LFm-8J-A Metal Normally closed (N.C.)

CYV

Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and

7.4

O-ring Port plug Body Ported Base Mounted Blanking plug (For One-touch fittings) KJP-02 A L Dimensions [mm] Applicable fitting size d Model A L D Weight [g] 2 KJP-02 8.2 17 3 0.1 3.2 KQ2P-23 16 31.5 5 1 4 KQ2P-04 16 32 6 1 23 KQ2P-04 D Silencer (For manifold EXH port) Body Ported Base Mounted Silencer is installed in the EXH port.

7

set of a, b, c, d) BMA3-050 (A set of a, b, c, d) BMA3-063 (A set of a, b, c, d) CKQ D-M9ANote 2) BMA3-040S (A set of a, b, c, e) BMA3-050S (A set of a, b, c, e) BMA3-063S (A set of a, b, c, e) Auto switch Switch bracket (Resin) Transparent (Nylon)Note 1) d e White (PBT) c Switch holder b Auto switch mounting screw a * Band (a) is mounted so that the projected part is on the internal side

IDG

When air with high purity is required, please either mount the above separator on the outlet side or use a made-to-order product (refer to page 14-19-50), which is provided with a micro mist separator (Series AWD) instead of a regulator. 3.