VCL (mm) A B C D E F G H J L Port size Bracket part no.
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be offset, which results in the generation of a lateral load that can cause malfunction.
7 w i t q Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com A A' @6 #2 @8 @9 #0 !8 !9 #1 @7 !4 !
a place that will be used as a scaffold during piping.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
When installing a paddle on IF3O type, piping may be interfered with by the tip of a paddle. Because this is used to detect a small flow rate, and to narrow the distance between a paddle and piping, additional machining of the paddle tip may be necessary to eliminate interference between the two. 6. Use pipe fittings that comply with JIS specifications.
Please consult with SMC for the supply of a pressure gauge with NPT port threads. Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it will may result in a breakdown. For sealing, use a sealant tape. Flow rate (L/min (ANR)) ARP IR-A Option/Mounting Bolt Assembly IR Model Part no. Dimensions Qty.
(Pages 10, 12, 15, 17) L-Tees Combine an elbow with a Tee. Mixed sizes of barbed branches are available. (Pages 9, 11, 15, 17) V-Tees orient the barbed branches on adjacent hex surfaces. Mixed branch sizes are available. (Pages 10, 12, 15) 1/8 NPT Male manifolds Hundreds of combinations for the OEM needing a fitting that requires a minimum amount of labor to install.
B 1.8 1.6 Groove position of auto switch A 10.4 12.8 Model MHK2-12 MHK2-16 A B Dimensions A and B of other models are same as standard switch grooves. Standard switch grooves 12-6-17
92 M64 X 2 110.0 Use a single knuckle joint or a double knuckle joint individually.
B 1.8 1.6 Groove position of auto switch A 10.4 12.8 Model MHK2-12 MHK2-16 A B Dimensions A and B of other models are same as standard switch grooves. Standard switch grooves 12-6-17
VHS2500 VHS3500 VHS4500 VHS5500 Model 1/8 1/4 1/4 3/8 1/4 3/8 1/2 3/4 1 1(P)/2(A) Piping port 1/2 1/4 1/8 3/8 3(R) 110 (6.11) 130 (7.22) 16 (0.89) 31 (1.72) 10 (0.56) 14 (0.78) 22 (1.22) 38 (2.11) 57 (3.17) 1(P) 2(A) Effective area (mm2) (Cv) 2(A) 3(R) Combination with a modular style FRL is possible. 33 (1.83) 40 (2.22) 14 (0.78) 29 (1.61) 11 (0.61) 16 (0.89) 15 (0.83) 29 (1.61) 51 (2.83
DIN rail mounting adapter is mounted onto a screw mounting type controller afterwards.
The cylinder should be operated using a connection method which allows for shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting method is shown in Figure 1.
Use the table as a guideline for mounting. Auto switch mounting bracket part no. BMG2-012 Auto switch part no. D-M9(V)/M9W(V)/M9A(V) Note) Use a screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5). The tightening torque should be 0.5 to 1 Nm. As a rule, it should be turned about 90 beyond the point at which tightening can be felt.
H 2-P Port size 2-P A B H 2-M Port size 2-M Thread depth N L L K K Conduit terminal: T F (Q) 34 25 U R C G (PF) 1/2 E B A H D 2-P Port size (S) 2-M L K N.C.
If touched inadvertently, there is a danger of being burned.
(A cylinder with 4 bore has been added as a compact type to the existing CJ2: 6 double acting cylinder.)
) -37No.PS-OMU0002CN-D () OUT1 [AP1 REdY] (OUT1[AP1 REdY] 1 [AP2 REdY]) OUT1 OUT1 OUT1 [AP1 RUn] ([AP1 RUn] 1 [AP2 REdY]) OUT2 P_1 H_1(n_1 H_1)[AP2 REdY] (OUT2[AP2 REdY] 1) OUT2 OUT2OUT1OUT2 [AP2 RUn] ([AP2 RUn] 1) P_2 H_2 (n_2 H_2 ) OUT1 P_1=A-(A-B)/4 n_1=B+(A-B)/4 A= H_1=(A-B)/2 H_1=(A-B)/2 B= OUT2P_1n_1H_1P_2n_2H_2 1 -38No.PS-OMU0002CN-D [F 5] FUNC /FUNC 0 56[F97]
VN LVC LVA LVH Variations LVD LVQ Valve Material Base, Body Seal Aluminum NBR, FKM, EPDM LQ Common SUP Individual SUP Common SUP Individual SUP Port A Port A Normally closed (N. C.) LVN Port P TI/ TIL Port P Port P PA Port A PAX Port A Port A PB Normally open (N. O.)