Rotary Gripper Series MRHQ Note 1) Values do not include auto switch mass.
Adjustable Rod Lever/VM830-01-14 JIS Symbol 2.3N F.O.F.
o 0.62 322 1.28 14 oaa {4) 250 u-24 0.50 .621 .621 0.25 0.93 0.38 1t-1E .251 .250 0.75 0.25 0.34 0.75 o.75 o.1a cts16 0.75 120 o.62 3.19 3.8:t 343 t06 {17-l _312 6t-21 0.50 .621 .621 0.38 1 . 1 2 0.38 5t-i E .25r .250 0.75 0.25 o.3a 3.97 o.8a o_aao.24 qi-14 o.75 1.30 0.62 334 1.25 125 t 2 5 t 1 k ) 375 \-24 o.aE .749 .749 o.11 r.32 0.50 .251 o.25 0.41 rt.4 1.06 r.06 0.25 sa-l6 0.46 r.62 0.78
D -DIN connector DL -DIN connector with light DO-For DIN connector (without connector) Orifice and port size combinations T -With conduit terminal TL-With conduit terminal/light Class Orifice diameter Port size 2 3 4 5 7 10 1/8 (6A) 2 1/4 (8A) 1/4 (8A) 3 3/8 (10A) 1/2 (15A) Connector 1/4 (8A) 3/8 (10A) 4 All class B coils are equipped with surge voltage suppressor.
Do not operate a cylinder with its bumper bolt removed. If the bumper bolt is removed, the piston hits the head cover, causing damage to the cylinder. Therefore, do not use a cylinder without a bumper bolt. 2. The piston rod must be retracted when mounting the cylinder.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. Caution Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model. 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only.
When mounting the product, please do not block the exhaust port at the center of the body as this may cause performance issues.
22.5 52h9 0 0.074 +0.030 0 +0.052 0 43 30H9 3-4H9 depth 4 5 4 ( A , B , C ) 3-R2 3-R2 2-6.6 through 21.5 10.5 16 5 53.5h9 0 0.074 7 6 43 23 10.5 46 4 13 Angle adjustment bolt 2-6.6 through 72 13 Adjustment: Max. 10.3 6 2 M5 x 0.8 2 8 A port 1 B port +0.030 0 3-4H9 long groove depth 3 8 g6 0.005 0.014 ( A , B , C ) 16h9 0 0.043 4-M6 x 1 depth 11 50 0 0.074 53.5h9 48 11-5-14 14 Series MSUA
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Please do the vacuum aspiration according to customer's specification.
Please do the vacuum aspiration according to customer's specification.
Refer to pages 16-14-3 and 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Wiring Pressure Source Warning Warning 4. How to connect contact protection box Connect the lead wires from the body and the contact protective box side indicated SWITCH.
Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-113 for Precautions on every series. q u w e 1 3 LOW i o 2 4 r Selection !0 t Caution !1 1. Select the model taking into consideration the material suitable for the operating fluid.
(Type B) VCW 20 1 G Lead wire length Series 300 mm 600 mm 1000 mm 1500 mm 3000 mm Nil L1 L2 L3 L4 20 30 40 Class 2 Class 3 Class 4 Clip Voltage Electrical entry 1 2 3 4 5 6 36 Flat head screwdriver 100 VAC 200 VAC 110 VAC 220 VAC 24 VDC 12 VDC 230 VAC G D DL DO C T TL Grommet DIN terminal DIN terminal with light DIN terminal (without connector) Conduit Conduit terminal Courtesy of Steven
Note 2) Do not release the OUT side piping port of the product directly to the atmosphere without connecting piping. If the product is used with the piping port released to atmosphere, accuracy may vary.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
(Fig. 1) Also, do not use the cylinder with fixed at external slider to avoid excessive moment applied to bearing of the cylinder.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
O ver range of i nput si gnal Pl ease execut e "i ni t i al i ze ( ref er t o P16) " w hen I TV do not operat e norm al l y af t er rest art i ng t he pow er suppl y. Readi ng or w ri t i ng errors occurred i n EEPRO M . Pl ease cont act us, w hen I TV do not operat e norm al l y af t er i ni t i al i ze.
Free mount Speed controllers do not protrude from the top of the body. Top mount Bottom mount Side mount Wiring and piping direction can be selected depending on mounting conditions.