HAA Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Holder Insert bushing end Tubing Tubing Caution Caution J and K type clamps do not move. If the tubing slips, adjust the adjustment screw with a flat head screwdriver. Turning the screw clockwise will make the tube gripping force stronger. Type J Type K Adjustment screw 4 Press fit the insert bushing. Slowly operate the lever to press fit the insert bushing to the tubing.
(The test was performed with the electric actuator in the initial state.) 8) Do not use the product in an environment where it is exposed to oils such as cutting oil, and water. Please install an appropriate protective countermeasure.
Do not service machinery/equipment or attempt to remove component until safety is confirmed. 1) Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 4-17-4
Function plate (With gasket) Note) DXT152-14-1 Mounting screw NXT013-3 Qty. 1 pc. 2 pcs. A B Note) DXT060-51-13B, DXT152-14-1B are for energizing continuously.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Note) For other voltages, please contact SMC. 3-12-1 A Series VFN2000N Dimensions (mm) VFN2120N--02 148 19 23 Applicable heavy-duty cord O.D.6 to 8 Pg9 37 24 66.5 57 32 40 14 Pilot EXH. 2-5.5 Mounting hole 3-1/4 3 4 5 1 Manual override (Non-locking) 23 23 VFN2220N--02 224.5 19 23 Applicable heavy-duty cord O.D.6 to 8 Pg9 24 66.5 57 32 40 14 Pilot EXH. 2-5.5 Mounting hole 189 3-1/4 3 4 5 1
Direction of work piece conveyance RSG-B Adjustable shock absorber stroke type (98 + Stroke) Stroke Adjustment bolt 13.5 Note 6) 14 Note 6) 20 60 24 Note 6) 25 A 4-9 through 110 + Stroke 177 + 2 Strokes 67 + Stroke Approx. B With cancel cap RSG-C Dimensions when equipped with cancel cap are the same as in the drawings above.
Do not dispose this fluid in the environment.
Wiring Power supply and N/A communication connector Power LED Communication LED Fig.1 Display and Communication * Please don't do the insert and remove of live-wire after the power supply is turned on. It causes the communication abnormality with the master by the situation.
. * Refer to page 14 for procedures for changing the stopper bolt and switch positions and for top cover replacement instructions.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only. They can cause the coil to burn out. 3.
If you do not do this air-bleeding, there would be the great danger of unexpected accident, such as shooting out of parts when they are being unscrewed.
Do not Do not Do not Do not Do not Do not Do not Do not Do not Do not D o D o D o D o It is recommended to keep the ground wiring distance as It might cause fire accident, malfunction and cylinder cable, apply excessive stress, or place heavy material onto malfunction occurring.
Do not ground to water pipe, gas tube Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. . Do not connect too many wires to the same outlet, which could results in heat generation and fire. .
Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. 8. Do not retrofit the wiring of the dryer and the power supply line. 9.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire.
Do not operate in an atmosphere containing flammable, explosive or corrosive gas. Fire or an explosion can result. This product is not designed to be explosion proof. Do not use the product for flammable or highly permeable fluids. A fire or explosion can result. Do not use the product in a place where static electricity is a problem.
Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. 8. Do not retrofit the wiring of the dryer and the power supply line. 9.