Solenoid Valve Avoid using these products in machinery/equipment which affects human safety, and in cases where malfunction or failure can result in extensive damage. operation, otherwise it may be impossible to guarantee safety due to unexpected malfunction or erroneous operation. 14. Do not use in places where there are cyclic temperature 2.
For details of each setting, refer to page 14 of this manual. Please refer to the PLC manufacturer's manual etc. for details of programming and addresses. For the PLC protocol and programming refer to the relevant manufacturer's documentation.
Measure the voltages at both sides of the power supply for CompoNetTM. 14 VDC to 26.4 VDC Investigate the cause of the voltage fluctuation, and take countermeasures against it. Confirm the voltage is within the specified range.
Check the key-lock function. 14 Buttons do not work. Product failure Replace the product. Effect of line pressure fluctuation because hysteresis is too narrow or delay time of the switch is too short (1) Adjust the set pressure value. (1) Check the set pressure values (hysteresis) (2) Change the response time setting. (2) Check the delay time. The operation is unstable.
Insert the cover. 14 XL*-OMJ0003-D Revision history Safety Instructions Po Limited warranty and Disclaimer SR 1st Printing :JT 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2012 SMC Corporation All
(Take care not to damage the surface of the seal mounting groove.) 14 XL-OMV0016 7-3. Assembly Procedure Step 1 Preparation Step 2 Reassembly of bellows assembly Apply a spanner to the width across the flats of the shaft to prevent it from rotating. Note) For XLAV-16/25, mount the washer in the orientation that the groove of the washer faces to the valve seal 2.
(Figure-14) Figure-14 6-3-4. Seal installation 1) Piston seal () Rub grease into the seal groove and outer circumference of piston after installing it. (Figure-15) Grease 2) Tube gasket () Mount the tube gasket on the cover. Figure-15 Caution Make sure that there is no abnormal operation or air leakage when assembly is completed. 16 - 6-4. Consumable parts 6-4-1.
The buttons cannot be operated. 14 Product failure Replace the product. Check that the panel mount adapter and the product are correctly assembled. Mount the product on the panel correctly. Incorrect installation 15 The product is loose. Product failure Replace the product. Rework the piping.
For type W, DC voltage For connector cable of M8 connector, is only available. refer to page 13 and 14. Note 1) Enter the cable length symbols in CE-compliant: For DC only.
The buttons cannot be operated. 14 Product failure Replace the product. Check that the panel mount adapter and the product are correctly assembled. Mount the product on the panel correctly. Incorrect installation 15 The product is loose. Product failure Replace the product. Rework the piping.
Low line voltage (1) Faulty wiring (2) Blown fuse of disconnection lead wire (3) Poor contact at contactor wire or connection part (4) Broken coil wire (5) Foreign matter caughtin armature Changeover plate is not placed properly. (14) Though pilot valve does shift, main valve will not shift or wilbe sluggish.
Installation Method . 14 2-1. Run Mode . 14 2-2. Maintenance timing for emitter detection . 15 2-3. Indication/Setting Parts Description . 15 3. Selection and Setting of Product . 16 3-1. Sensing DC Mode . 16 3-2. Pulse DC Mode . 20 3-3. DC Mode . 25 3-4. Power supply cable wiring diagram . 27 4. Specifications . 29 4-1. Ionizer. 29 4-2.
SAFETY INSTRUCTIONS 14 2. APPLICATION 5 3. SPECIFICATIONS 5 4. HOW TO ORDER 6 5. TROUBLESHOOTING 7 6. CONSTRUCTION / PARTS LIST 89 7. REPLACEMENT PROCEDURE 1012 8. DISASSEMBLY DRAWING 1314 9. DIMENSIONS 15 REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
Operation and Mounting 2.1 Air Supply -P. 5 2.2 Operating Environment -P. 6 2.3 Design -P. 6 2.4 Mounting and Installation -P. 8 2.5 Piping -P. 11 2.6 Speed Control -P. 12 2.7 Shock Absorbing Mechanism -P. 12 2.8 Directional Control -P. 14 2.9 Mounting of Auto Switch -P. 14 3. Maintenance and Inspection 3.1 Inspection -P. 15 3.2 Maintenance -P. 15 3.3 Replacement Parts -P. 15 4.
In addition, in the case of trouble, please send it back to the supplier for repair or replacement. 14 No.VF1000-OMN0002-A S Revision history A Safety Instructions PP 1st printing : oQ 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation
To prevent air leakage, re-wind the sealant tape and fit into the changed location when the piping port location is changed. 14 Auto Switch Handling Precautions Magnetic field resistant auto switches, D-P79WSE and D-P74, are special switches for cylinder with strong magnet built-in, and they are not interchangeable with standard auto switches and cannot be used for general cylinders.
In addition, in the case of trouble, please send it back to the supplier for repair or replacement. 14 SV1000*-OME0002-C Revision history CRENEWAL 2020.6 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer
PRODUCT NAME Solenoid Valve MODEL / Series / Product Number SQ Series (Pilot Valve V100) Contents Safety Instructions -2,3 Precautions on Design -4,5 Selection -4,5 Mounting -5 Piping -5 Wiring -6 Lubrication -6 Air Supply -6 Operating Environment -7 Maintenance -7 Specific Product Precautions -8 to 10 Valve construction -11 to 14 Manifold Options and How to Increase Manifold Stations.
Do not apply external force to the pilot valve. 14 SMC will investigate. The following information is required for investigation, so please send it to your sales representatives.
Dimensions for installation n: number of valve stations n L 1 2 3 4 5 6 7 8 L1 120.7 136.7 152.7 168.7 184.7 200.7 216.7 L2 80 96 112 128 144 160 176 n L 9 10 11 12 13 14 15 16 L1 232.7 248.7 264.7 280.7 296.7 312.7 328.7 344.7 L2 192 208 224 240 256 272 288 304 (mm) The above table shows dimensions as an example for the SY5000 series valve manifold.