Series: 3 (VQZ300), Stations: 14 Stations, Option: None, Thread: 00T
Piping: 21 (Body Ported), Stations: 14 Stations, A, B Port: 00T (NPTF)
Piping: 20 (Body Ported), Stations: 14 Stations, A, B Port: 00T (NPTF)
Stations: 14 Stations, Option: D (DIN Rail Mounting), Port Size: 00T (NPTF)
Stations: 14 Stations, Option: D0 (DIN Rail Mount w/o DIN Rail), Port Size: 00T (NPTF)
Stations: 14 Stations, Option: None, Port Size: 00T (NPTF)
POWER CLAMP CYLINDER Do not disassemble, except for when replacing any of the replaceable parts, as this may cause the performance to deteriorate. (8) Proximity switch output The switch output signal is output near the clamping end and the unclamping end respectively.
Type 20) 3 110 VAC, 50/60 Hz Nil Push type (Safety style) G H L LN L plug connector With lead wire 600 mm lead wire 300 mm lead wire 4 220 VAC, 50/60 Hz Grommet B Locking type (Tool required) 2 Body side exhaust (Type 30, 50) 5 24 VDC 6 12 VDC C Locking type (Manual) Without lead wire Without connector With lead wire Without lead wire Without connector MO With connector D Without connector DO
Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series. Pressure Setting Wiring Warning Warning 1. Setting of vacuum pressure 1. Do not apply excessive pulling force on the lead wire. It may cause a malfunction or damage. 2.
Do not block the bleed hole. If the bleed hole is blocked, the product will not operate properly. VBA VBAT AP100 875
Do not hurt the body seat during installation. Compression of the O-ring of the mating side of the body shall be 0.7 to 0.9mm.
If operating pressure is over the range then cylinder will be damaged and injury by broken pieces. (4) Do not put your hand into the slit of the body without confirming safety. Injury and Bodily harm will occur with the valve operated when valve is operated valve. (5) Do not remove the Cover Fig.1 29 on the actuating part.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Cut the end of the tubing at a right angle and pass it through the fitting nut. After placing the tubing in the holder, push it onto the insert bushing until it stops and clamp it with the knob.
Identifying Version Symbols For versions lower than V2.0 and S2.0: Do not use with controller parameters higher than V2.0 or S2.0. Applicable models Applicable models JXC91m Series JXCD1m Series JXCP1m Series JXCE1m Series For versions higher than V2.0 and S2.0: Do not use with controller parameters lower than V2.0 or S2.0.
Display for Wireless Base 14 3.2.1. Information tab 14 3.2.2. Input/Output monitor tab 16 3.2.3. Setting tab 20 3.3. Display for Wireless Remote 30 3.3.1. Information tab 30 3.3.2. Input/Output monitor tab 32 3.3.3. Setting tab 36 3.4. Detailed information of units 41 3.4.1. Information tab 41 3.4.2. Details of I/O monitor tab 50 4. Setting Function 57 4.1. Edit TAG 57 4.2.
Display for wireless master 14 3.2.1. Information tab 14 3.2.2. Input/Output monitor tab 16 3.2.3. Setting tab 20 3.3. Display for wireless slave 30 3.3.1. Information tab 30 3.3.2. Input/Output monitor tab 32 3.3.3. Setting tab 36 3.4. Detailed information of units 40 3.4.1. Information tab 40 3.4.2. Details of I/O monitor tab 49 4. Setting Function 56 4.1. Edit TAG 56 4.2.
Display for wireless master 14 3.2.1. Information tab 14 3.2.2. Input/Output monitor tab 16 3.2.3. Setting tab 20 3.3. Display for wireless slave 30 3.3.1. Information tab 30 3.3.2. Input/Output monitor tab 32 3.3.3. Setting tab 36 3.4. Detailed information of units 40 3.4.1. Information tab 40 3.4.2. Details of I/O monitor tab 49 4. Setting Function 56 4.1. Edit TAG 56 4.2.
All Rights Reserved 14 XL-OMM0005-A
Single vane Adjustment range of adjustment bolt (B) Adjustment range of adjustment bolt (A) 90 162 1 25 (S): 10 (S): 10 180 161 90 90 262 3 30 180 260 90 440 7 50 180 436 22.5 90 675 20 60 180 671 Positioning pin hole Allowable Load Adjustment bolt (A) Adjustment bolt (B) Do not permit the load and moment applied to the table to exceed the allowable values shown in the table below.