AXTS-OMY0007 Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
for attaching a limit switch Applicable product Kit no.
A A A Description Material Note Parts list Description Material Note Parts list MGPM63 to 100MGTM MGTL Carbon steel Spring guide Parallel pin Parallel pin Flat cylinder w/turntable MGPL63 to 100High carbon chromium bearing steel Guide plate Bearing guide A Bearing guide B Bearing guide C Bearing guide D Aluminum alloy Aluminum alloy Aluminum alloy Aluminum alloy Aluminum alloy Carbon steel
Units display (Accumulated flow) Units display (Instantaneous flow) Warning: WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
(For accumulated increment) [H_1 ] Setting of Hysteresis [ 300] 300 L/min (PF3A706H) Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
IDX-OM-W011-B / Series IDF1E/2E/3E-10(-A,C,S) IDF3E-20(-A,C) IDF4E-10(-A,C,L,M,R,S,T) IDF4E-20(-A,C,L,M,R,T) IDF6E-10(-A,C,K,L,M,R,S,T) IDF6E-20(-A,C,K,L,M,R,T) IDF8E-10(-A,C,K,L,M,R,S,T) IDF8E-20(-A,C,K,L,M,R,T) IDF11E-10(-A,C,K,L,M,R,S,T) IDF11E-20(-A,C,K,L,M,R,T) IDF15E1-10(-A,C,K,L,M,R,S,T) IDF15E1-20(-A,C,K,L,M,R,T) URLhttps://www.smcworld.com/ English instruction manual can be downloaded
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. The following instructions must be followed during maintenance: Turn off the power supply.
Do not apply a lateral load to the external slider. When a load is mounted directly to the cylinder, variations in the alignment of each shaft center cannot be offset, which results in the generation of a lateral load that can cause malfunction.
7 w i t q Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com A A' @6 #2 @8 @9 #0 !8 !9 #1 @7 !4 !
a place that will be used as a scaffold during piping.
1 Free Mount Cylinder for Vacuum Series ZCUK A free mount cylinder with a vacuum passage in the rod to meet the requirements for Air cylinder + Vacuum pad .
(Pages 10, 12, 15, 17) L-Tees Combine an elbow with a Tee. Mixed sizes of barbed branches are available. (Pages 9, 11, 15, 17) V-Tees orient the barbed branches on adjacent hex surfaces. Mixed branch sizes are available. (Pages 10, 12, 15) 1/8 NPT Male manifolds Hundreds of combinations for the OEM needing a fitting that requires a minimum amount of labor to install.
VS7
A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent setting, use the following part numbers for ordering. 3. Secure the plate before mounting the load. Load mounting without securing the plate may cause galling of the piston rod, leading to particle generation.
M Applicable tubing b Applicable tube a B A Reducer: M-32R-2, M-04R-2 Applicable tubing O.D. x I.D.
The cylinder should be operated using a connection method which allows for shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting method is shown in Figure 1.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.