EXxx-OMU0020CN Configuration table(Valve Module Digital I/O) Properties . 4-10 (. EX245-DY1) 28 No.EX-OMU0020CN 4.3.5.3. FSU (Fast Start Up) EX245-SPN1 (FSUFast Start UpFSU)FSU FSU 4.3.5.3.1. EX245-SPN1 PROFINET Properties PropertiesOptionsConnectionTP / ITP 100Mbps full duplex,Disable autonegotiation . 4-11 PROFINET FSU 29 No.EX-OMU0020CN 4.3.5.3.2.
ST(I) () LED PLC H.T. ON/OFF ST(I) () ON/OFF LED PLC H.T. ST(O) () 4 DME DMF H.T. ON/OFF LED PLC ST(O) () ON/OFF ST / :(66 ) -29No.EX-OMQ0015CN EX600No. LED PLC H.T. () 0 1 5 AXA / ( () )/ / LED PLC H.T. () () 6 AYA ( )/ / :(66 ) -30No.EX-OMQ0015CN EX600No. H.T. () LED PLC 0 1 7 AMB / ( () / )/ / / (SI ) ON/OFF H.T.
Communication to the higher level safe controller is disabled Module connection Connect the SI Unit, the I/O modules and the End plate using the 2 modular adaptor assemblies and a joint assembly.
I Insulation resistance Insulation resistance of the product. The resistance between the electrical circuit and the case. K Key-lock function Function that prevents changes to the settings of the product (disables button operation). M Manual pressure setup without using auto preset. This term is used to distinguish between manual and auto preset pressure setup.
Item Default setting Indicator LED (OUT1) [ L] L/min [F 0] [Un i] Unit selection function Indicates the output status of OUT2. LED is ON (Red) when OUT2 is ON. When the accumulated pulse output mode is selected, the indicator LED will turn OFF.
Selection of connected sensor [ 10] 10 L/min (PFM510) [F 0] [Un i] Unit selection function [ L] L/min The zero clear function has been performed while the fluid is flowing. "Er4" will be displayed for 1 second. Perform the zero clear function again under no flow conditions. Attaching the connector to the sensor wire Strip the sensor wire as shown. Do not cut the insulator.
Hysteresis mode I Instantaneous flow The volume of flow per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
Hysteresis mode I Instantaneous flow The volume of flow per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
Hysteresis mode I Instantaneous flow The volume of flow per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
Verify the specifications before use. [ Un i] Unit selection function 1 [ L] L/min Default settings When the flow exceeds the set value [P_1], the switch will be turned ON. When the flow falls below the set value by the amount of hysteresis [H_1] or more, the switch will turn OFF. If the operation shown in the diagram below is acceptable, then keep these settings.
Hysteresis mode I Instantaneous flow The volume of flow per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
Hysteresis mode I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
[F95] [LPm] L/min [Un i] Unit selection function [F99] [ in i ] Reset to the default settings [oFF] Unused Maintenance Connecting / Disconnecting When mounting the connector, insert it straight into the socket, holding the lever and connector body, and push the connector until the lever hooks into the housing, and locks.
Hysteresis mode I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
Hysteresis mode I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
Hysteresis mode I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. Insulation resistance Insulation resistance of the product. The resistance between the electrical circuit and the case. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON.
Hysteresis mode I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. Insulation resistance Insulation resistance of the product. The resistance between the electrical circuit and the case. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON.
Hysteresis mode I Instantaneous flow The volume of flow per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
. -16No.PF-OMW0010-D Terms Meaning I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.
I Instantaneous flow The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through the device in 1 minute. The voltage drop across the product (and therefore not applied to the load), when the switch output is ON. The voltage drop will vary with load current, and ideally should be 0 V.