EX600-SPN_eng Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. OFF. Parameter Setting Hardware Configuration I/O Map Diagnostic Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do the same for release (push and rotate for 90 degrees). Tighten the piping using the correct torque shown below.
Caution Mounting 1) Do not subject the gauge to shocks, such as dropping during transportation and mounting, as this can cause loss of indication accuracy. 2) Do not use this gauge in a location with high temperature and humidity, as this may cause faulty operation. 3) When mounting the pressure gauge, be certain to use a wrench on the square wrench flats to screw it into place.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Caution Do not disconnect the USB cable during Teaching. If disconnected, the actuator will stop suddenly and the servo will be turned OFF.
Do not load the Card Motor with continuous or higher thrust than allowed for a prolonged time. When a pushing operation step data is selected, the pushing force is continuously generated from [Operation Start] until [Operation End (Stop)] is pressed.
Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr confirmed. 3. Do not service or attempt to remove pr 3. Do not service or attempt to remove pr 3.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not use fluid containing solid matter. This will cause faulty operation. IR IRV VEX SRH SRP SRF SRF ITV IC ITVH ITVX PVQ VY1 VBA VBAT AP100 891
for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 708 MHY2 Series 180 Angular Type Air Gripper Cam Type MHY2-20D 2 x M5 x 0.8 thread depth 8 Pin hole positioning (Mounting thread) 14 5 19 42 4H9 + 0.030 depth 4 0 4 x M4 x 0.7 through (Thread for mounting attachment) 8 4 x M5 x 0.8 thread depth 10
10 1.2 12 76 34 8.1 10 50.4 60h9 61h9 28H9 9 17H9 10 6 2.5 6.5 17 8.6 14 8.5 8 34.7 70 17 18.5 10 1.2 12 84 37 10.5 10.5 53.5 65h9 67h9 32H9 12 22H9 10 4.5 3 6.5 17 8.6 14 8.5 10 39.7 80 19 21 12 1.6 15.5 100 50 12.4 12.5 60.6 75h9 77h9 35H9 13 26H9 12 5 3 7.5 20 10.5 18 10.5 (mm) JC JD JJ JU JV Q S SC SD SU UU WA WB WC WD WE WF XA XB XC YA YB YC Size 10 20 30 50 M8 x 1.25 12 M5 x 0.8 M4
30 6.8 6.6 12 16 M6 X 1 M8 X 1.25 116.5 14 372 354 186 190 124 158 118 73 106 144 140 64 30.5 43 286 40.5 35 8.6 8.5 14 15 M8 X 1.25 M10 X 1.5 Model FF II NN AA BB CC DD EE GG JJ KK LL MM WW XX ML1C25 ML1C32 ML1C40 1/8 5 5 5 5 7 28 26 14 44 20 16 12.5 120 42 1/8 6 5 6 5 8 36 28 18 54 36 18 12.5 140 48 1/4 30.5 6 5 6 5 8 47 17 62 30 22 16.5 170 51 4.7-8 Hy-Rodless Cylinder SeriesML1 Stroke
N Nil Rc 3 1 0 14 to 60 l/min 20 to 1500 l/min 36 to 2600 l/min NPT Specifications Water/Non corrosive liquid Copper alloy Fluid Stainless steel 304 Liquid, which do not corrode stainless steel 304. Max. pressure 1 MPa 1.75 MPa Water resistance Insulation resistance 100 M (500 DC by megameter) 1500 VAC for one min.
Stainless steel Cover Steel plate Body Aluminum die-casted Hexagon bolt Stainless steel C B D Width across flats PAT. 7 A Freeze reduction type/Option VCHNF Sleeve guide Resin Sleeve Copper tubing -06 to 14 3 4 AN VCHN (mm) AMC Model Port size (R) A B C D Mass (g) VCHN3-06 VCHNF3-06 VCHN3-10 VCHNF3-10 VCHN4-10 VCHNF4-10 VCHN4-12 VCHNF4-12 VCHN4-14 VCHNF4-14 3/4 200 72 74 41 590 AMV 3/4 200
Note 6) The display unit is comformed to CE mark. 14 Series PF2W Flow Characteristics (Pressure Loss) PF2W720, PF2W520 PF2W740, PF2W540 PF2W704, PF2W504 0.030 0.05 0.07 0.025 0.06 Pressure loss (MPa) 0.04 Pressure loss (MPa) Pressure loss (MPa) 0.020 0.05 0.03 0.04 0.015 0.03 0.02 0.010 0.02 0.01 0.005 0.01 0 0 0 10 12 14 16 2 0 4 6 8 40 35 30 25 20 15 10 5 0 4.0 3.5 3.0 2.5 2.0 1.5 1.0
Do not use an application to operate several cylinders simultaneously by adjusting cylinder speed. If this is inevitable, use a high rigid guide against load, so that the cylinder is not damaged even when the each cylinder output is slightly different. 4.
Series: 2 (VQZ2000), Stations: 14 Stations, Option: None, Thread: 00T
Series: 1 (VQZ1000), Stations: 14 Stations, Option: D (DIN Rail Mounting), Thread: 00T