AD402/600 Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not operate at pressures, temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction. Please contact SMC when using a fluid other than compressed air. We do not guarantee against any damage if the product is used outside of the specification range. 2.
Do not put hands or fingers between the plate and body. Care should be taken that hands or fingers do not get caught in the space between the cylinder body and the plate when air pressure is applied. 1. Do not scratch or dent the sliding parts of the piston rod and guide rods. Damage to seals may cause air leaks or faulty operation. 2.
Do not disassemble the parts that are not explained in this operation manual. This may decrease the performance and life expectancy of these parts. In addition, disassembly may cause danger. Torque values specified in this manual must be followed. Not adhering to these specifications, can result in damage to the product. 12 XL*-OMI0009-E 6-2.
Do not apply excessive force or impact. This will not only damage the product but also decrease its performance and life expectancy. It is not possible to disassemble the bonnet assembly of this product. If the components and assembly are damaged, or damage is expected, exchange the bonnet assembly itself. Do not disassemble the parts that are not explained in this operation manual.
Do not use valves in such environments where corrosive gases, chemicals, or brine or water or steam is airborne, or where valves can be directly exposed to any of those. 2. Do not use in an explosive environment. 3. Do not use in locations influenced by vibrations or impacts. 4. A protective cover, etc., should be used to shield valves from direct sunlight. 5.
In-line D-M9N D-M9P D-M9B D-M9NA D-M9PA D-M9BA Electrical entry Special function Wiring (Output) Indicator light Applicable load Smbol A B C E F G 3-wire (NPN) 3-wire (PNP) 2-wire Relay, PLC IC circuit 24 V 5 V, 12 V Grommet Yes 12 V Yes 3-wire (NPN) 3-wire (PNP) 2-wire 24 V 5 V, 12 V Relay, PLC IC circuit Water resistance (2-color display) Grommet 12 V Option (For detail, refer to page
VDC C Locking type (Manual) Without lead wire Without connector With lead wire Without lead wire Without connector MO With connector D Without connector DO Light/Surge voltage suppressor 9 Other LO M MN Option Nil None M plug connector S With surge voltage suppressor Z With light/surge voltage suppressor Indicator light is not available for grommet type.
Page 4 6 8 10 12 19 1/8" 3/16" 1/4" 3/8" 1/2" Material: Super PFA LQHB LQHB TL TIL TL TIL TL Metric Size TLM TILM TLM TILM P.948 TD TID TD TID TIL Inch Size TH TIH TH TIH Material: PFA 2, 3, 4, 6, 8, 10, 12, 16, 19, 25 TLM Metric Size From page 949 1/8", 3/16", 1/4", 3/8", 1/2", 3/4" 1", 1 1/4" TILM Inch Size 4 6 8 10 12 1/8" 3/16" 1/4" 3/8" 1/2" 4 6 8 10 12 1/8" 3/16" 1/4" 3/8" 1/2" 3/4"
B 12 B 12 B 12 B 12 7 8 1 2 3 4 5 Valve stations EX600-ED4 1 set EX600-WEN1 1 set EX600-EU1 1 set SS5Y3-10S6WE72-05B-C6 (Type 10 5-station manifold base, Wireless EtherNet/IP) Negative common, M12 connector IN/OUT pin arrangement 1, I/O unit: 2 stations * SY3100-5U1 3 sets (2-position single part no.) * SY3200-5U1 2 sets (2-position double part no.) * EX600-DXPD 1 set I/O unit part no.
Description Piston seal 1 2 large 1 small 2 1 each large and small 2 1 2 Governor assembly 4 3 Check valve 2 4 Gasket 2 Rod seal 5 1 8 8 12 6 Mounting screw 12 7 Cover C assembly 1 Grease pack 1 1 2 1 2 The grease pack has 10 g of grease.
12 1 R25 74 Stroke 2-M5 X 0.8 14 8 144 4 12 Pressure port at rear side Pressure port at front side 70 4.5 2-Plug 12 18 36 40 (Digonal47) Basic type: RSH20-15ll SRSH20A, #1 (#1+#5) With locking mechanism: RSH20-15ll-D SRSH20A, #2 (#2+#5) With cancel cap: RSH20-15ll-C SRSH20A, #3 (#3+#5) With lever detection switch: RSH20-15ll-S SRSH20A, #4 (#4+#5) With locking mechanism + cancel cap:
Do not allow it to idle for a long time. If the pump is operated for a long time without any fluid inside or in a gas-fluid mixed state, the diaphragm may be damaged or the life may be shortened. Do not continue idling for 3 minutes or longer. 10.
No output Reduction of the set pressure Unstable set pressure Delay in increase of the downstream pressure Operating environment Warning (1) Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. (2) Do not operate in a location subject to vibration or impact.
An injury or failure can result. 3 Step Setting Mode Maintenance Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not exceed specified current or the LED might be damaged and not function. 3. The indicator light is lit when switch is off for D-P70 4. Do not drop, dent, or allow excessive impact to cylinder during handling. 5. Keep at least 20mm away from each other when 2 or more cylinders with high magnetic field resistance auto switch are mounted in parallel. and D-P75.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Cross pointed driver Torque driver Tightening torque 0.60.05 Nm See Check item for tightening torque of two screws. 12 8.
Do not cover the inlet and outlet vents.