Related Products: Heavy Duty Auto Drain Series ADH4000 Services 15 Sebaai Street, Miami 21411 Alexandria, Egypt TEL: 3-548-50-34 FAX: 3-548-50-34 PAKISTAN (Distributor) Jubilee Corporation First Floor Mercantile Centre, Newton Road Near Boulton Market P.O.
I/O monitor(I/O ) 15 2. Diagnosis Data() 24 3. Sys. Configuration() 27 4. Parameter Setting() 33 5.
If using the product to detect very small flow rates, warm up the product for 10 to 15 minutes first. There will be a drift on the display or the analogue output of approximate 2 to 3% immediately after the power supply is turn on, within 10 minutes. Check regulators and flow adjustment valves before introducing the fluid.
The maximum operating 0 5 10 15 20 25 30 ( temperature for the valve is 150oC. If the heater temperature is over 200oC or valve temperature is Time (sec.) Duration of the inrush current flow (as a guide) over 150oC, please use thermostat to control the heaters to prevent overheating.
20 25 30 ( 30 10 XL-OMY0001 5 5-1 1 , SUS304 8 4 SUS304 10 , SUS316L 7 5 A6063 2 1 6 SUS304 3 2 9 2 SUS304 SUS304 11 XL-OMY0001 5-2 C E E E KF K Fd Fn C D H B A G A mm A B C D E Fn Fd G H XLA-16-2 40 108 38 20 30 17 44 XLA-25-2 50 121 48 27 12 40 26 44 XLA-40-2 65 171 66 39 11 55 41 67 XLA-50-2 70 185 79 46 11 75 52 72 XLA-63-2 88 212 100 55 11 87 95 70 76 XLA-80-2 90
Step 7 Reassembly of bonnet assembly (No.2) 3 Bolt 1 2 4 Bonnet assembly Pilot port Bolt size, Tool, Tightening torque of bolt (Nm) valve Bolt size Hex Tightening size wrench torque XLF-16 M3 3 0.7 -25 M5 4 1.5 -40 M6 5 2.5 -50 M8 6 6.1 -63 M10 8 15 -80 Body Supply air pressure of 0.4MPa (G) to the pilot port.
Step 6 3 Bolt b Tightening torque of bolt a Nm 1 Tightening torque of bolt b Nm Valve size Tightening torque 2 Valve size Tightening torque 4 All sizes 0.3 XLA-16 0.7 -25 1.5 -40 2.5 -50 6 Bonnet assembly -63 6 -80 15 -100 20 Bolt a Heater Pilot port -160 102 Cover Body Apply 0.4MPa of air pressure to the pilot port.
(Refer to page 41) -33No.EX-OML0011-C 1. Selection of parameter Explanation of screen a) Name of each parameter to be set b) The next parameter is displayed with the and buttons. c) Parameters that can be set in each unit only. d) Parameters that can be set in each channel only. 2.
Do not block the exhaust port of the ejector. 15 - Doc. no. ZQ-OM00801-D Air Supply Use clean air. 1. Using compressed air which contains chemicals, synthetic oils containing organic solvents, salts or corrosive gases, etc. can cause damage or malfunction. Do not use compressed air containing toxic impurities. 2.
If the heater 0 5 10 15 20 25 30 ( temperature is over 200oC or valve temperature is over 150oC, please use thermostat to control the heaters to Time (sec.) Duration of the inrush current flow (as a guide) prevent overheating. With PTC type heaters, there is an initial surge of current (inrush current) after the power is supplied. These inrush current will reduce overtime.
General 3 positions 5 positions General 15 Setting (continue) 1.Stroke adjustment General 3 positions 5 positions General Adjust the stroke of actuating part. 1-1 Loosen fixing bolt, move the unit to the position where required stroke is obtained and fix the unit by the bolt. 1-2 E-MY2C/H Loosen lock nut for adjusting bolt for fine setting of stroke by the bolt.
Nominal10 2.6N ) Square embedded pressure gauge Applicable model Process Procedure Tools Check items Disassembly Remove the pressure gauge cover Rotate the pressure gauge cover 15 counterclockwise to pull out the pressure gauge cover.
Nominal10 ) Square embedded pressure gauge Applicable model Process Procedure Tools Check items Disassembly Remove the pressure gauge cover Rotate the pressure gauge cover 15 counterclockwise to pull out the pressure gauge cover.
Bracket B Model Tool Tightening torque AL20-D AL30-D 0.75+/-0.2 N m Phillips screw driver AL40-D AL50-D 1.5+/-0.2 N m AL60-D Set screw (2 pcs.) -15- 8. Operation and Adjustment 8-1. Adjustment of Dripping Amount Oil regulating valve While supplying air, rotate the oil regulating valve to adjust the amount of oil.
51 110 130 210 3.5 5.9 7.9 16 23 34 0.35 0.24 0.16 0.35 0.25 0.16 0.1 0.2 VNA2-15A VNA2-10A VNA1-10A 3 8 15 0.3 0.4 1 2 3 4 VC VNA3-20A 20 0.5 0.6 Note) This product cannot be used for water application.
MHZ2-20D3 Bgre size Height 8 '19 Low profile oesrgn 25 20 41 Reduced bendinq moment and vibralion O . The low profile design saves space and reduces bending moments C o . lmproved accuracy with smooth operation a Vi,.tilthlwml WWI 50 Height is approximately 1/3 the size of an equivalent Series MHZ2.
reduction 41 to 140F (5 to 60C) Note 3) Ambient and fluid temperature Note 1) It indicates the inlet pressure for solenoid valve.
Services 15 Sebaai Street, Miami 21411 Alexandria, Egypt TEL: 3-548-50-34 FAX: 3-548-50-34 PAKISTAN (Distributor) Jubilee Corporation First Floor Mercantile Centre, Newton Road Near Boulton Market P.O.