3/5 Port Solenoid Valve When connecting power to a solenoid valve with a DC specification and a light or surge voltage suppressor, check for polarity. If the polarity connection is wrong, the valve will not operate. 2. Applied voltage: 2. Install an air filter. When electric power is connected to a solenoid valve, be careful to apply the proper voltage. Improper voltage may cause malfunction or coil damage.
VK300-82-2-01 VK300-82-2-03 110 VAC 110V 200 VAC 200V VK300-82-2-02 VK300-82-2-04 220 VAC 220V VK300-82-2-07 VK300-82-4-51 VK300-82-4-06 VK300-82-3-05 VK300-82-3-53 240 VAC 240V 6 VDC 6V 12 VDC 12V 24 VDC 24VD 48 VDC 48VD 3-2-11
pilot Solenoid VCC 1 2 1 2 3 TQ 629 A VNH Series Construction !
0.8 2 port M5 x 0.8 Note) V114(A) and V124(A) cannot be mounted to the same manifold.
Hs 34.5 41.5 49.5 58.5 A 9 9 9.5 11 Hs 37.5 44.5 52.5 61.5 A 2 2 2.5 4 Hs 35.5 42.5 50.5 59.5 A 5 5 0 1 Hs 39 46 54 63 A 5 5 5.5 7 Hs 33 40 48 57 Size A 4.5 4.5 5 6.5 Hs 32 39 47 56 Hs A 10 10 10.5 12 MLGC 25 32 40 50 CNG 0.5 2 56.5 66 MNB Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200
As a countermeasure, install a 2-way valve or a check valve. However, please note that when a check valve is installed, if the cracking pressure is high, defective suction may occur. (As a guide, the cracking pressure should be 0.02 MPa or less.) 2. Mounting Caution 1. Read the operation manual before mounting the product.
(A value under a specified condition.) VN LVC LVA Electricity LVH 1. Apparent power (VA) Volt-ampere is the product of voltage (V) and current (A). Power dissipation (W): For AC , W = V/A cos. For DC, W = V/A (Note) cos shows power factor. LVD LVQ 2. Surge voltage The surge voltage is a high voltage generated momentarily when cutting the power supply. LQ 3.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
Hs 34.5 41.5 49.5 58.5 A 9 9 9.5 11 Hs 37.5 44.5 52.5 61.5 A 2 2 2.5 4 Hs 35.5 42.5 50.5 59.5 A 5 5 0 1 Hs 39 46 54 63 A 5 5 5.5 7 Hs 33 40 48 57 Size A 4.5 4.5 5 6.5 Hs 32 39 47 56 Hs A 10 10 10.5 12 25 32 40 50 0.5 2 56.5 66 Operating range Minimum strokes for auto switch mounting (mm) (mm) D-A7H, D-A80H D-A79W D-F7, D-J79 D-F7W, D-J79W D-F7BAL, D-F7NTL D-F7F Bore size 25 Auto switch
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
Product part number Auto drain number Normally closed Normally open HAW2-04C/D AD402-04C-6-A AD402-04D-6-A HAW7-06D AD402-04D-6-A HAW22/37-14D AD600-06 HAW55/75-20D AD600-06 HAW110-30D AD600-10 2) The drain piping, if conducted, should have an inside diameter of at least 10mm and a maximum length of 5m.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
21.7 20 79.1 22 40.4 1 Reference dimensions 6 AS Series Dimensions DIN Rail Mounting Bracket L-Bracket Bracket on a single side Bracket on a single side AS1002F AS2002F L17 L16 L15 L12 L13 L14 L23 L22 L24 L11 t1 t2 2 x D5 2 x D6 L21 L20 L19 L10 L9 L18 L25 AS2052F AS3002F AS4002F L23 L22 L24 2 x D6 L21 L20 L19 L18 Part no.
Signal 1 Pitch Magnetic section Non-magnetic section 0.2 0.1 0.3 Movement A phase B phase Signal 2 q A scale of magnetic layers and non-magnetic layers with a pitch of 0.8mm is cut into the piston rod. w With movement of the piston rod, a sin, cos 2-phase signal (Signal 1) is received by the magnetic resistance element.
Note 2) Since sizes 20 and 25 have a body with type B (Through-hole) and type A (Both ends tapped style) in common, there is no type A part number. Example) RQA 20-30 does not exist.
As a countermeasure, install a 2-way valve or a check valve. However, please note that when a check valve is installed, if the cracking pressure is high, defective suction may occur. (As a guide, the cracking pressure should be 0.02 MPa or less.) 6 2. Mounting Caution 1. Read the operation manual before mounting the product.
Select a model such that the upstream pressure is lower than the back pressure generated when the exhaust flow rate is at a maximum. 4. Exhaust flow speed characteristics are shown in graph 2. 1. Operate giving consideration to the effects of turbulence on dust, etc., that has settled on the floor or other areas. 2.
Select a model such that the upstream pressure is lower than the back pressure generated when the exhaust flow rate is at a maximum. 4. Exhaust flow speed characteristics are shown in graph 2. 1. Operate giving consideration to the effects of turbulence on dust, etc., that has settled on the floor or other areas. 2.
Select a model such that the upstream pressure is lower than the back pressure generated when the exhaust flow rate is at a maximum. 4. Exhaust flow speed characteristics are shown in graph 2. 1. Operate giving consideration to the effects of turbulence on dust, etc., that has settled on the floor or other areas. 2.
M5 x 0.8 Port 2 M5 x 0.8 Note) 10-V114(A) and 10-V124(A) cannot be mounted on the same manifold.