Series AS Elbow Type/Universal Type Speed Controller with One-touch Fitting 1 2 !3 !4 !5 !6 !7 !8 q w e r t y u i o !0 !1 !2 !3 !4 !
2 #2 !6 !4 @4 #3 !8 #7 #8 o #6 q #9 y i $2 @3 @2 #1 @6 #4 #5 Component Parts Note Anodized Nickel plated Chromated Note No.
Operation time: 2 sec./min. Motor operated auto drain is packed together with main unit.
switch 12 V 5 V, 12 V 12 V 5 V, 12 V 12 V 2-wire J79C Connector M9NWV M9PWV M9BWV M9NAV M9PAV M9BAV 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 4-wire IC circuit Relay, PLC Diagnostic indication (2-color indication) 24 V Yes Grommet IC circuit Water resistance (2-color indication) F79F With diagnostic output (2-color indication) IC circuit 5 V,12 V 3-wire (NPN
If a small flat head screwdriver is inserted between the opening in the bottom, terminal block (3) will be removed from the housing (2). (Refer to Figure-1.) 4) Remove the cable gland (4) and plain washer (5) and rubber seal (6). 2.
Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered,whichever is first. *2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
ON OFF Time 5 Manual setting/Auto preset MPa or kPa OUT1 OUT2 CH 1 2 3 4 PRESSURE Auto preset mode Manual set mode SET Press button. SET CH1 setting is completed when the channel display changes from blinking to lights on.
In the case the alarm cant be reset by above manner, repair is required. ERR02 System error 2 #1 and #2 change when [ ] or [ ] is pressed. Indicates control operation mode during normal operation and set values during setting mode selection.
2-wire Connector RB Diagnostic indication (2-color indication) Grommet 3-wire (PNP) 3-wire (NPN) J IC circuit 5 V, 12 V Grommet 12 V 2-wire DConnector Relay, PLC Yes 24 V 3-wire (NPN) 5 V, 12 V Diagnostic indication (2-color indication) IC circuit 3-wire (PNP) -X Grommet 2-wire 12 V With diagnostic output (2-color indication) IC circuit 5 V, 12 V 4-wire (NPN) 20Lead wire length symbols
Consult P/A when the use in such environment is required. 3.Do not use in direct sun light. 4.Do not use in environment where there is heat source. With shock absorber 2.
OUT(2) 1 Thread type Rc NPT G Nil N F IN(1) Voltage 1 2 3 4 5 6 36 100 VAC 200 VAC 110 VAC 220 VAC 24 VDC 12 VDC 230 VAC Port size Class 3 Port size 1/8 (6A) 1/4 (8A) Class 2 Class 4 Symbol 01 02 03 04 06 3/8 (10A) 1/2 (15A) Class B in AC has a rectifying circuit built-in. Class H is AC only. No rectifying circuit.
The above CSA NRTL/C logo is described on a product label in order to indicate that the product is approved by CSA and UL Standards. TSSA (MCCR) Registration Products TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi (0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation.
Attachment . 13 4-2. Protection cover . 14 4-3. Mounting to duAro flange . 15 4-4. Angle Adjustment of the Moving Direction of the Finger . 16 4-5. Piping . 17 4-6. Speed controller . 17 4-7. Finger open / close speed adjustment . 18 4-8. Connection of the auto switch and sensor harness. 19 5. Operating method or operation . 19 5-1. Precautions for Design . 19 5-2. Air supply . 19 5-3.
Safety Instruction .2 2. Outline.6 3. How to Order.7 4. Specification.7 5. Mounting .7 5-1. Electrostatic sensor installation.7 5-1-1. Sensor head installation.7 5-1-2. Installation of the sensor amplifier.8 5-2. Circuitry and wiring chart.9 6. Performance.10 6-1. Output signal.10 6-2. Detection range.11 6-3. Cautions on installation .11 6-4. Timing chart .12 7.
Note 2) The maximum operating temperature for the solenoid valve is 50. Note 3) The effective area listed is for a single solenoid 2 position valve mounted on a sub-plate.
1A S Valve seal Assy (4) Specific XLD40-2-9-1A ** XLD50-2-9-1A ** XLD63-2-9-1A ** XLD80-2-9-1A ** Standard AS568-009V AS568-016V AS568-016V Initial pumping valve seal (5).
Symbol Nil N T F Thread type Rc NPT NPTF G VCW23-5G-2 .. 5 sets Valve part no. (Stations 1 to 5) Series "" is the symbol for mounting. Add a "" in front of the part numbers for solenoid valves, etc. to be mounted. 2 3 4 Class 2 Class 3 Class 4 Enter together in order, counting from station 1 on the D side.
If a small flat head screwdriver is inserted into the gap between housing (2) and terminal block (3), terminal block (3) will be removed from housing (2). (See diagram at the top right of the page.) 4) Remove cable gland (4), washer (5) rubber seal (6).
A contact protection box is not required for solid state auto switches due to their construction. 1. Where the operation load is an inductive load. 2. Where the wiring length to load is greater than 5 m. 3. Where the load voltage is 100/200 VAC.