Ionizer Gun Static neutralization range (Discharge time of 1000V100V) . 19 5-3. Pressure Flow characteristics . 20 6. Dimensions . 20 7. Specifications . 22 8. Troubleshooting . 23 2 Doc. no.IZ*-OMX0012-B Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
Bracket B Model Tool Tightening torque AFM20-D Phillips AFM30-D screwdriver 0.75+/-0.2 N m AFM40-D Set screw (2 pcs.) -19- 8. Operation and Adjustment 8-1. Discharge from the product with drain cock Pressurize the inside of the mist separator when discharging drain. Drain will not be discharged properly if not pressurized.
Valve diagnostics 2 Table. 5-5 Valve diagnostics 2 Bit Description Explanation 0 Valve 16, 17 diagnostics 0: No error, 1: Short circuit 1 Valve 18, 19 diagnostics 0: No error, 1: Short circuit 2 Valve 20, 21 diagnostics 0: No error, 1: Short circuit 3 Valve 22, 23 diagnostics 0: No error, 1: Short circuit 4 Valve 24, 25 diagnostics 0: No error, 1: Short circuit 5 Valve 26, 27 diagnostics
Dimensions . 19 7. Specifications . 21 1 - Doc. no. IZ*-OMT0002 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
For the operation in normally open and normally closed, refer to "List of output mode" on page 19.
Lateral Load 1 0.8 16 Allowable load at rod end (N) 0.6 0.4 10 0.2 6 4 0 0 10 20 30 40 Stroke (mm) 19 Pneumatic circuit The typical circuit for CJP2 series where air filter, regulator, solenoid valve and speed controller (meter-out) are used for operation is as follows.
. -18 SY3000*-OMJ0003-A Specific Product Precautions 12 Be sure to read before handing. 14 SY3000*-OMJ0003-A -19- Specific Product Precautions 13 Be sure to read before handing. 14 SY3000*-OMJ0003-A -20- Specific Product Precautions 14 Be sure to read before handing. 14 SY3000*-OMJ0003-A -21- Specific Product Precautions 15 Be sure to read before handing. No. No.
Maintenance and Inspection 3.1 Inspection -P. 19 3.2 Maintenance -P. 20 3.3 Replacement Parts -P. 20 4. Troubleshooting -P. 20 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Perform this detection procedure in the absence of workpiece. 19 Doc.No.IZ-OMK0015D 3-2. Pulse DC Mode (1) Bar length selection -Select the appropriate length suited for a work size by referring to the static neutralization characteristics, static neutralization area, etc.. (2) Ionizer body installation Install the Ionizer within 50 to 2000mm.
UW 1st printing: SS 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2012 SMC Corporation All Rights Reserved 19 XSA-OMS0001-A
Port (3) Rod seal (2) Seal retainer (1) Retaining ring Fig. 5 Replacement of rod seal 19 - 3-2.
HOW TO ORDER" (P8). 19 8REPLACEMENT PROCEDURE WARNING Before replacement, ensure that the regulator is not pressurized. Rotate the pressure adjusting handle to zero. Replace refering to 9DISASSEMBLY DRAWING P24 to P28. After replacement, ensure that specified function is satisfied and external leakage is not found before starting operation.
REPLACEMENT PROCEDURE 19-22 11. DISASSEMBLY DRAWING 23 12. DIMENSIONS 24 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Allowable load mass on guides and moment 17/28 18/28 19/28 20/28 21/28 22/28 5.
(The tightening torque should be about 2 to 3 Nm.) (5) Modification of the detecting position should be made in the condition of 3. 17 A Table 2 Table 3 18 19 Table 4 A 20 Table 5 A 21 A Table 6 22 Table 7 23 Table 6. Auto switch Connection and Example 24 3. Maintenance 3-1.
(chattering) (1) Correct the wiring (2) Correct the wiring conditions (reduce the tensile force and increase the bending radius). 19 (1) Check the power supply wiring. Incorrect wiring or broken lead wire (2) Check if there is bending stress applied to any parts of the lead wire.
Insufficient tightening of the bolt Foreign matter is caught in the gap betw een the mounting surfaces (19) Abnormal amount of air leakage is found from the 3 (R) port. Foreign matter is caught in the poppet valve on the exhaust side. (3) (6) Foreign matter is caught in the poppet valve on the supply side.
Symbol Number of arranged elements 4 7 13 19 Number of arranged elements 30 36 55 83 04 07 13 19 30 36 55 83 Symbol Nominal filtration accuracy (m) Note) Nominal filtration accuracy (m) 0.5 1 2 5 10 20 40 Symbol Nominal filtration accuracy (m) 50 70 74 75 100 105 120 X50 001 002 005 010 020 040 050 070 074 075 100 105 120 Symbol Element length Element length L250 L500 (L250 x 2) L750 (L250
setting so that the indicator is lit in red to ensure the detection at the proper position of the air gripper. 530 MHR3/MDHR3 Series Rotary Actuated Air Gripper 3-Finger Type Model/Specifications Nominal size 15 10 Action Double acting External grip 13 7 Holding force (N) (Effective value) (1) at 0.5 MPa Internal grip 12 6.5 Finger closing width (mm) Finger opening width (mm) Stroke (mm) 19
Model Gripping force N (Effective value at 0.5 MPa) Note 1) External Internal Open/Close stroke (Diameter) Port size Lubrication Nominal size Weight g Note 2) Action Model Finger opening width (mm) Finger closing width (mm) Stroke (mm) 11221122125 (130) MHR3-10 MDHR3-10 MHR3-15 MDHR3-15 Vacuum suction type 10 7 6.5 16 22 6 M3 x 0.5 Double acting Non-lube 11221122230 (235) 15 13 12 19 27 8