Fieldbus system EtherNet/IP TM compatible SI unit Refer to failure 13. The analogue input or output device does not work correctly. Refer to failure 14. Contact SMC. -37No.EX-OMN0032-D Trouble counter measure method No. Part No. EX600Problem Presumed cause Troubleshooting 1 LED is OFF. Power supply for control and input is OFF. Check if the power for control and input is supplied. Red LED is ON.
Construction 13-14 6. Spare Parts 14 7. Made to Order 14 2 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Content 0 to 7 0Eh: The number of bytes of the system diagnosis information (fixed to 13 bytes). System diag.1 7 6 5 4 3 2 1 0 Byte 7 Bit No.
Filter element (11) ZB1-FE3-A Filtration rating: 30m, 10 elements in one set [For suction filter] (12) Silencer [For silencer] ZB1-SE1-A 10 silencers in one set Pressure sensor (13) ZB1-PS-A assembly Pressure switch (14) ZB1-ZS-A assembly for vacuum Manifold base (15) ZZBFor changing the number of stations assembly 32 - Doc. no.
Dimensions 13 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
For details of each setting, refer to page 13 of this manual. Please refer to the PLC manufacturer's manual etc. for details of programming and addresses. For the PLC protocol and programming refer to the relevant manufacturer's documentation.
If a workpiece is still being held, there is a danger of it being dropped. 13 - 4-2.
Not adhering to these specifications, can result in damage to the product. 13 XL-OMV0016 7-2.
(kPaMPa can be selected) Improper model selection (Selection of model "without Units selection function") Check if there is a "-M" at the end of the part number printed on the product The display units cannot be changed. : The units selection function 13 is not available in Japan due to a new measurement law. : It is fixed to the SI unit "kPa", "MPa".
ZL-OM00801 Contents Safety Instructions 2 Model Indication and How to Order 10 Mounting and Installation 12 Air Supply 12 Supply Pressure 13 Piping 13 Solenoid Valve 15 Construction 15 Maintenance and Inspection 17 Exhaust from Ejector 19 Specifications 19 Circuit Diagram 22 Weight 23 Exhaust Characteristics and Flow Characteristics of Ejector 24 Flow Characteristics Curves 25 Vacuum Pressure
Refer to page 13 for ordering coil only. 11 Construction/Principle Parts Material 12 Solenoid Coil Assembly 13 Trouble shooting If abnormal operations occur while in use, please check the following flowchart and take the appropriate measures.
Improper model selection (selection of model "without units selection function") Check if there is an "-M" at the end of the part number printed on the product (kPaMPa can be selected) The display units cannot be changed. : The units selection function is 13 not available in Japan due to a new measurement law. : It is fixed to the SI unit "kPa", "MPa".
Note 4) Apply pressure from P port in the base for interface regulator. 13 No.SYJ3000-OMM0002-A TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
[Number of emitter cartridges/Bar weight] Bar length (mm) 300 380 620 780 1100 1260 1500 1900 2300 Number of emitter cartridges 3 4 7 9 13 15 18 23 28 Weight (g) 330 400 600 720 1000 1100 1500 2000 2500 29 Doc.No.IZ-OMK0015D 4-2.
Auto switches When an auto switch is mounted or its set position is changed, refer to pages 13 to 18. C a u t i o n Use a specific mounting bracket (Table 2) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque.
90 3.2 AR60K-B 70 66 65.8 11 13 90 3.2 Note 1) B dimension is a size in the state to unlock the handle.
HOW TO ORDER" (P8). 13 2) Bowl assembly / Auto drain for AW30-B Option Semi-standard Semi-standard Standard Semi-standard J Part no. Port thread Port thread Part no. Rc Rc C3SF-J-A C3SF-A G G C3SFF-J-A NPT C3SF(-Z)-A NPT C3SFN-J(Z)-A B B External B Semi-standard 6 Semi-standard 6J appearance drawing and Port thread Port thread Part no. Part no. part no.
(See Fig. 12) 40 or more Fig. 12 -13- 7. If attaching the workpiece magnetically, the auto switch may stop working due to a loss of magnetic force in the cylinder depending on the mounting position. Allow a clearance of 5 mm or more between the auto switch and workpiece. Fig. 13: Auto switch mounting on the cylinder side Fig. 14: Auto switch mounting on the guide side 3.
Isolate the valve and re-tighten the bolts. (13) (14) Lessen the oil supply amount to the degree that oill does not spout out of the exhaust port [3(EB), 5(EA), PE port]. *In the case of N.O. specification, 1(P) port. (15) Supply specified pressure to X port.
SV1000-OME0002-C Solenoid Valve PRODUCT NAME SV Series MODEL / Series Contents Safety Instructions -2, 3 Precautions on Design / Selection -4, 5 Mounting -5,6 Piping -6 Wiring -6 Lubrication -6 Air Supply -7 Operating Environment -7 Maintenance -7,8 UL approved -8 Specific Product Precautions -9 to 11 Construction -12 Trouble shooting -13 Remedy -14 1 SV1000*-OME0002-C Safety Instructions