PFMV3.eng Mounting screw (M3 x 5 L) Function selection mode Panel mount adapter (can be rotated 90 degrees for mounting). Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Troubleshooting Wiring Wiring of connector Connections should only be made with the power supply turned off.
Mounting by panel mount adapter Fix the panel mount adapter to the controller by the mounting screws M3 x 8 L (2 pcs.).
2 VN*-OMJ0001-B / / / / 1 1 1 1 1 1 1 1.5 .5 .5 .5 *3) *3) *3) *3) 1 1 1 1 1 1 1 1 () 3 VN*-OMJ0001-B 1)-5 2) ( ( ( ( ) ) ) ) () IP IP IP IP65 65 65 65 1) 50mm 2/s 2) 3) 1) 2) 5m 3) 4) 1.5~2 2 4 VN*-OMJ0001-B 3)0.1MPa Nm Rc1/8 79 Rc1/4 1214 Rc3/8 2224 Rc1/2 2830 Rc3/4 2830 Rc1 3638 Rc1 1/4 4042 Rc1 1/2 4850 Rc2 4850 ( ( ( ( 5, 6, 7 5, 6, 7 5, 6, 7 5, 6, 7 ) ) ) ) G1/2 M3
Table 3-5 Signal cable Terminal specification Cable specification Terminal block Recommended screw diameter crimp terminal M3 1.25Y3 0.75 mm2 (AWG18) Shielded cable 3.3 Installation HRS Series 3-18 HRX-OM-S004 Chapter 3 Transport and Setting Up 3.3.5 Wiring of run/stop signal inputRemote signal input Run/Stop signal input and remote signal input enable the product to operate/stop or switched
HRSH Series 3.2 Installation 3-7 HRX-OM-Q026 Chapter 3 Transport and Setting Up Table 3-2 Amount of radiation and required ventilation Required ventilation amount (m3/min) Heat Differential temp. of 3 oC between inside Differential temp. of 6 oC between inside Model radiation (kW) and outside of and outside of installation area installation area HRSH100-A-20/40Approx.18 305 155 HRSH150-A-
Table 3-2 Amount of radiation and required ventilation Required ventilation amount (m3/min) Heat Differential temp. of 3 oC between inside Differential temp. of 6 oC between inside Model radiation (kW) and outside of and outside of installation area installation area HRS200-A-46-S Approx.37 615 310 Installation at indoor site The products splash-proof specification is IPX4.
Model Bolt Max.tightening Torgue (Nm) JMHZ2-16D M3 x 0.5 0.59 Attachment 16 - How to Mount Air Gripper (1)Mounting to the robot arm (2)Mounting of the cover Take care not to get the switch cable caught when mounting the cover.
Model Bolt Max.tightening Torgue (Nm) JMHZ2-16D M3 x 0.5 0.59 Attachment 15 How to Mount Air Gripper Adjust the robot arm position before mounting so that the mounting is easy. (1) Mounting to the robot arm (2) Mounting of the cover Take care not to get the switch cable Caught when mounting the cover.
Model Bolt Max.tightening Torgue (Nm) JMHZ2-16D M3 x 0.5 0.59 Attachment 14 How to Mount Air Gripper Connector storage Set the three connectors at the end of the robot hand according to the characters printed on the flange. The connection part of the connectors are set in the direction of the arrows.
JMHZ2-16D-X7400B-HC10-(*) P13P14P15 4 M6 31.5 2XM4x0.7 8 4 M6 108.8L 4 4 M4 4 M3 27 17 10 - JMHZ2-16D-X7400B-HC10DT-(*) 4 M6 32.5 8 4 M6 109.8L 4 4 M4 4 M3 27 17 11 - 3-6. M8 8 M8-Molex P .19 NPN PNP No. 1 +24V DC24V 2 GND DC0V 3 ON/OFF() 4 ON/OFF() 5 () 6 () 7 8 Molex (51227-0800) M8 8 12 - 3-7.
Refer to the table below Bolt pull Model Belt Pull tension Model Bolt size Tightening [N] Part number torque [Nm] EQFS25 LE-D-15-1 19.6 EQFS25 M3 0.6310% EQFS32 LE-D-19-1 49.0 EQFS32 M4 1.510% EQFS40 EQFS40 LE-D-19-2 70.0 19 - "Pulley plate" is installed.
Loosen the hexagon socket head cap screws (M3 x 30:2 locations) which are fixing the SI unit. 2. Separate the SI unit to valve manifold. 3. Add and increase the attached tie-rod (2 pcs. per block) to the increased block respectively and pass through a block by the tie-rod. 4.
Caution (1)For M3, M5, 10-32UNF Tightening method (10)Do not apply excessive force or shock to For M3 First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a hexagon wrench. Refer to Table below for reference. the body or fittings with an impact tool.
The terminal screw is an M3 cross head screw. Note: Connect the ground terminal to ground. Resistance to ground should be 100 ohms or less. A. Single power supply used B.
Insulation resistance 1000 M Withstand voltage 1000 V Operating temperature range -30 to +55 oC VCTF 2 core cable (0.75 mm2 x 2) VCTF 4 core cable (0.75 mm2 x 4) Use the M3 crimped terminal for the connection.
The terminal screw is an M3 round head combination screw. Terminal Connection BS+ Connect the communication power supply BS+. BDH Connect the communication cable BDH. BDL Connect the communication cable BDL. BSConnect the communication power supply BS-.
B RATE Terminal board Terminal Connected to MS+ BS+ of communication power line BDH BDH of communication line BDL BDL of communication line BSBSof communication power line FG Ground line 24V 24V of solenoid valve power line 0V 0V of solenoid valve power line M3 terminal screw in use. EX##-OMF0012 8 EX##-OMF0012-A No.EX-OMF0012-B -9- 5-3. Address setting (1) ADDRESS NO.
Tightening torque (1) Round head combination screw (M2.5 x 41): 0.3 to 0.36 Nm (4) Hexagon socket head cap screw (M3 x 30): 0.6 to 0.66 Nm Replacement procedure of ZL212-SP01 (Silencer set) Disassembly and Reassembly 1. Remove the four round head combination screws (M2.5 x 53) (1). 2.
Applied voltage When connecting fittings to valves, tighten as indicated below. 1) M3, M5 types 1. When using SMC fitting, follow the guidelines below. After tightening by hand, tighten an additional 1/4 (M3), 1/6 (M5) turn with a tightening tool. However, if miniature fittings are used, tighten an additional 1/4 turn with a tightening tool after tightening by hand.
SYJ7000 M3 0.8Nm Caution Replacement of Pilot Valve Pilot valve in this series are improved to provide excellent energy saving results. However following this improvement, these new valves are no longer compatible with the conventional pilot valve used at the interface.