XL-OMV0002 JIS B 8370: JIS B 8361: JIS B 9960-1: -(1 :) JIS B 8433-1993:*2) 1. 2. 3. 1. 2. 3. 4. 3 *3) 1 1.5 3) 1 1 () 4 1 1-1 MXQ6 MXQ8 MXQ12 MXQ16 MXQ20 MXQ25 1) 2) ( ) 3) 4) / / 2 ,3 ) 2 2 ,3 ) 1) 1 2) 20 ,0.150.6MPa 3) MXQ25(A)-150,MXQ6B-50,75MXQ8B-75,100MXQ16B-100,150MXQ20B-125,150 300mm/s 4) MXQ**B 50200mm/S 1 (MPa) MXQ8(A,C) 0.3 MXQ8B 0.3 MXQ12(A,C) 0.3 MXQ12B 0.3 MXQ16(A) 0.2
3 !2 i q !1 !4 y !9 Open condition Component Parts Note No.
TQ1230001-OM102-B 3. Specifications 3.1.
TQ1230001-OM104-C 3. Specifications 3.1.
Chemraz R is a registered trademark of Greene, Tweed & Co. 3.
Recommended Not recommended 3. To reuse the tubing, remove the previously lodged portion of the tubing.
3 e w t !3 A A !0 !2 !7 !6 o !5 !1 i !4 Section A-A u Parts list Material Note No. Description No.
ISG ZSM 3 0 3 Pressure [kPa] 100 Example) When the property at the temperature characteristic condition 3.0 [% F.S.] and 25[C] is expressed by the bold line in the chart above, how much temperature effect will the analog output voltage receive? The chart above illustrates the example when 100 [kPa], F.S. = 100 0 = 100 [kPa], 3.0% F.S. = 100 x 0.03 = 3 [kPa].
The shock absorber acts in the range between the rotating end and the angles shown table 3. 17 Table 2. Minimum rotation angle that will not allow decrease of energy absorption ability (Internal shock absorber type) Size 10 20 30 50 70 100 200 Minimum rotation angle that will not allow decrease of energy absorption ability 52 43 40 60 71 62 82 Table 3.
(Refer to Fig. 2) Fig. 2 (3) The appropriate terminating resistor varies depending on the CC-Link cable used. (Refer to the table and Fig. 3 below.)
Ground effect is not adequate by soldering the shield wire with wire rod to install the cable (Fig.2-3). 12.European Contact List (44) 1908-56 38 88 Hungary (36) 1-371 1343 Turkey (90) 212 221 15 12 Finland (358) 9-859 580 Portugal (351) 22 610 89 22 No.LC-OM08901 A (3/3) Denmark (45) 70 25 29 00 Poland (48) 22-548 50 85 Greece (30) 1-342 60 76 Switzerland (41) 52-396 31 31 France (33) 1-
TQ1230001-OM106-B 3. Specifications 3.1.
Special function Type Electrical entry Wiring (output) Indicator light Applicable load 0.5 (Nil) 3 (L) 5 (Z) DC AC Perpendicular In-line 5V 12V IC circuit 100V or less Reed switch Solid state switch A90 No A90V Relay PLC 2-wire 24V Grommet 12V A93 100V A93V Yes 3-wire (NPN equiv.) 3-wire (NPN) 3-wire (PNP) IC circuit 5V A96 A96V F9N F9NV IC circuit 5V 12V F9P F9PV 2-wire 12V F9B F9BV
F G H [Tightening torque] No.LZ-OM00401 B (1/3) Electric Cylinder LZC series L[]ZC[]3[] 1.5 8 M4 x 0.7 x 6 deep [0.75Nm ] L[]ZC[]5[] 3 13 M5 x 0.8 x 8 deep [1.5Nm ] L[]ZC[]3[] M4 screw 0.75Nm M4 screw 0.75Nm L[]ZC[]3[] 4.5 8 2 7.5 11.5 12 L[]ZC[]5[] 6.5 13 3.2 10.7 16.7 15 L[]ZC[]5[] M5 screw 1.5Nm M6 screw 2.6Nm Model no.
KP Series (with resin thread) 1) Winding of sealant tape Wrap the pipe tape 2 to 3 times around the threads, leaving 1.5 to 2 thread ridges exposed at the end of the threads. 2) Tightening After tightening by hand, tighten an additional 2 to 3 turns using a tightening tool. 2.
This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product. 3. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. 3.
Note) A: Non-locking push type A (projecting) 1 6A 8A 10A 10A 15A 20A 25A 32A 40A 50A 1 8 1 4 3 8 3 8 1 2 3 4 4 Note 2) 220 VAC 50/60 Hz 24 VDC 12 VDC 240 VAC 50/60 Hz Valve size 1 to 4 10 5 6 Note 2) Note) B: Slotted locking type B (tool required) 7 Note 2) 2 15 Note 1) CE-compliant: For D or DZ only Note 2) Semi-standard Note 3) For other rated voltages, please consult with SMC. 3 20 25