IDU/IDF Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
Therefore, do not use it with or expose it to the following chemicals: paint thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, watersoluble cutting oil (alkalinic), etc. 2. Do not expose it to direct sunlight.
Do not operate with anything other than compressed air. The cleaning equipment has been designed to be used only with compressed air. To use fluids instead of compressed air, please contact SMC beforehand. 2. Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases.
Do not use the product in applications where excessive external force (including vibration) or impact force is applied to it. Do not apply impact and vibration outside of the specifications; it may lead to a malfunction.
Do not connect black. Power supply/output connection lead wire Cable Specifications Pin no.
Do not operate in environments with corrosive gases, chemicals, sea water, fresh water or water vapor, or where there will be contact with the same. 2. In locations exposed to direct sunlight, block the sunlight. 3. Do not operate in locations where vibration or impact occurs. 4. Do not operate in a location near a heat source where radiated heat will be received. Pressure gauge 1.
Do not use in these conditions. (Refer to specifications.) 2. Do not use for power transmission These products are not designed to be used as bearings for transmitting power from a drive source, such as a motor. Such use may lead to rotation faults, or damage. Piping Caution 1.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specied procedures.
Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibrations and/or shocks. 4. Do not mount the product in locations where it is exposed to radiant heat.
Do not use in an atmosphere having corrosive ! Grommet gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. Class B coil: AWG20 Outside insulator diameter of 2.5 mm 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or q impact. 4.
DF 4-DT DH DS DA DL 4-DL B 90 DU DU DO DO DC Rotation DE Bore size (mm) A B A + B + 90 A 40 to 100 12 60 162 Note) This assembly drawing is provided as a reference.
Do not use in explosive atmospheres. 2. Do not use in locations subject to excessive vibration or impact. 3. Do not use in locations where radiated heat will be received from nearby heat sources. 0.4 to 0.6 1. Removing the product Shut off the fluid supply and release the fluid pressure in the system. Shut off the power supply. Remove the product. 2.
Do not attempt to rotate, as the connector does not turn.
Do not apply a load in excess of the specification limits. 1. Do not allow the table to hit the end of stroke. LEJ LEJ Select a suitable actuator by work load and allowable moment.
(Current output) Load Blue DC(-) NOTE : The unconnected terminals are used in SMC, so please do not connect them. Use the specified voltage. Use within the specified operating pressure. Do not drop, hit or apply shock to the Pressure Sensor. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire. Wire correctly. Do not perform wiring while the power is on.
Do not use in environments or locations where the equipment is exposed to cleaning solvent, etc. and oil film on rod may be washed away. Seals may break due to insufficient lubrication, causing air leakage. 13 - 4. Do not store cylinders in humid places. Humid environment should be avoided when storing cylinders.
If the piston speed increases excessively, internal parts, guides, etc. may be damaged. 5) Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction. 6) Do not dent or scratch the mounting surface of the body and the plate.