Process Pump Construction and operating principle -P.13 10. Operating principle P.13 11. Sensor mounting (leakage sensor) P.14 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Boards connected after the base are set as remote. 1 2 3 Operating conditions: ON ON OFF Cascade base ON OFF OFF Cascade remote Fig. 13 Base board . Example for cascade connection 1) Setting Cascaded board: 3 pcs.
Boards connected after the base are set as remote. 1 2 3 Operating conditions: ON ON OFF Cascade base ON OFF OFF Cascade remote Fig. 13 Base board . Example for cascade connection 1) Setting Cascaded board: 3 pcs.
(PI control) SV 5.4 Operation of Controller 5-13 A_HEC-OM-J004-4 Chapter 5 Operation <6> Heating proportional frequency setting / Mode indicator: Initial value: 2 sec. Setting range 1 to 120 sec. PV Heating for the proportional frequency setting Indicates that the heating for the proportional frequency setting mode is activated with Indicator .
Period and Scope of Warranty 13 7. Parts Replacement Procedure 14 1 XL-OMS0001-B Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Bit 13 System error 0x1811 Occurs when a system error . Bit 12 Solenoid valve error 0x1812 Occurs when a solenoid valve error . Bit 11 Internal communication error 0x1813 Occurs when an internal communication error . 4 Bit 10 Alarm generation Bit 8~9 of Byte 4 and Bit 7~4 of Byte 5 It is set when any of them is ON, otherwise it is 0.
Therefore, avoid designs where a single load is moved by synchronizing multiple cylinder operations. 12.Do not disassemble the product or make any modifications, including additional machining Doing so may cause human injury and/or an accident. 8 13.
CEU5 13 23m 23m () CEU5 11 AC 10 70500mm/s 12 6-2 5,6, 12 5 5,12 10 ?
No.D-S-OMI0002-C PRODUCT NAME Solid state auto switch MODEL / Series / Product Number D-F6# Series Table of Contents Safety Instructions 2 Model Indication and How to Order 11 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 13 Installation 13 Circuit diagram 14 Troubleshooting 15 Specifications 19 Specifications 19 Dimensions 20 Operating range 21 -1No.D-S-OMI0002
If the kinetic energy of the load exceeds the allowable value, it could damage the product, and cause a hazard to humans and damage the machinery and equipment. (13) Provide a shock absorber if the kinetic energy that is applied to the product exceeds the allowable value.
Please consult with SMC if a solid state auto switch can be used according to the environment. 13 - Do not use in an area where surges are generated.
Description 1 Body A 8 Lever shaft 2 Piston assembly 9 Seal support 3 Lever 10 Rod cover 4 Guide 11 Steel ball 5 Finger 12 Rod seal 6 Roller stopper 13 Piston seal 7 Body B 14 Gasket 7 12 6 4 10 9 8 13 Replacement parts Description JMHZ2-8 JMHZ2-12 JMHZ2-16 JMHZ2-20 Main part Seal kit JMHZ8-PS JMHZ12-PS JMHZ16-PS JMHZ20-PS 12,13,14 JMHZ2JMHZ-A0802 JMHZ-A1202 JMHZ-A1602 JMHZ-A1602 4,5,6,11
Dropping of work can be dangerous. 13 32 Structural drawing Parts List Component Parts No. Description Material Note Component Parts No.
Center of gravity .12 4Product Specifications .13 4-1. Air gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5. Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .16 5-3. CRX Plug-in software .20 5-4. Air supply .28 5-5. Piping .28 5-6. Operating environment .29 5-7. Lubrication .29 6.
Product Specifications . 13 4-1. Attachment . 13 4-2. Protection cover . 14 4-3. Mounting to duAro flange . 15 4-4. Angle Adjustment of the Moving Direction of the Finger . 16 4-5. Piping . 17 4-6. Speed controller . 17 4-7. Finger open / close speed adjustment . 18 4-8. Connection of the auto switch and sensor harness. 19 5. Operating method or operation . 19 5-1.
Product Specifications. 13 4-1. Air Gripper . 13 4-2. 3 Port Solenoid Valve . 14 4-3. Auto switch . 15 5. Operating method or operation . 16 5-1. Precautions for Design . 16 5-2. Installation . 16 5-3. TMComponent . 20 5-4. Air supply . 24 5-5. Piping . 24 5-6. Operating environment . 24 5-7. Lubrication . 25 6.
No.MH*-OMZ0003 / / JMHZ2-16D-X7400B-TM . 2 1. . 4 2. . 5 3. . 6 3-1. . 6 3-2. . 7 3-3. . 8 3-4. . 9 3-5. () . 10 3-6. . 11 3-7. . 12 4. . 13 4-1. . 13 4-2. 3 . 14 4-3. . 15 5. . 16 5-1 . 16 5-2. . 16 5-3.
Product Specifications . 13 4-1. Attachment . 13 4-3. Mounting to NEXTAGE . 15 4-4. Piping . 16 4-5. Speed controller . 16 4-6. Finger open / close speed adjustment . 17 4-7. Connection of the auto switch and sensor harness . 18 5. Operating method or operation . 18 5-1. Precautions for Design . 18 5-2. Air supply . 18 5-3. Operating environment . 19 5-4. Lubrication . 19 6.
It will cause failure of the controller or its peripheral devices. (13) Do not use the product in an environment subject to a temperature cycle. It will cause failure of the controller or its peripheral devices. (14) Do not use in a place where surges are generated.
IDH Series 1.1 Names and Functions of Parts 13 IDX-OM-W037 Thermo-dryer 2. Transportation / Installation Transportation and Installation Warning Use the product in the right way. Pay attention to personal safety during installation, operation, maintenance, and inspection.