AXTS-OMY0007 Mounting P 11 8. Environment P 11 9. Lubricant oil P 11 10. Air source P 11 -2 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Check for air leaks from the fitting and piping. (11) In case of air leakage from the interface, stop air supply and check the mounting condition of the gasket. Tighten the mounting screw with appropriate torque. If the countermeasures above are not effective, there may be a problem with the valve. In that case, stop using the valve immediately.
55 41 57 XLH-50 70 179.5 79 2 11 75 52 70 8 XL-OMY0003
5 10 []18 12 O 1) FKM M 10 FKM : 110 Pa <> 9 XL-OMY0003
6 6-1. 1 1P4P5 10 XL-OMY0003
6-2 1 2 b 3 1 2 O 4 a aa b O O
(Page 11) 6 - 2) Avoid having a large gap between the clevis or trunnion and mating bushing, as this exposes the pin to a bending load. 3) Do not let foreign matter such as cutting chips get into the product from the suction port. 4) Do not touch the cylinder during high speed and high frequency operation.
Nm (mm) 20 1.5 2.0 0.5 25 2.9 2.0 0.5 32 2.9 2.0 0.5 40 4.9 2.0 0.5 50 11.8 5.0 1.0 63 24.5 5.0 1.0 80 24.5 20.0 2.0 100 42.2 20.0 2.0 6 7 8 9 2-4. 1 2) 3 4 5 6 7 11 1 2 3 1.5~2 2 2. 12 2-5. ,AS 2-6. 2-6-1. CG5N 2-6-2. CG5A 11~2 2 31 4 5 6 7 13 2-6-3.
Pneumatic Circuit 11 6. Maintenance 11 6-1. Daily check 6-2. Regular maintenance 7. Troubleshooting 12 8. Basic Construction 13 Series MGJ Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
MWP*-OM0020Q-B PRODUCT NAME Air Press Cylinder MODEL/ Series/ Product Number MWP Series Contents Safety instructions 2,3 ActuatorsPrecautions 48 Air Press Cylinder Specifications Specifications 9 Operation Principle 10 Relationship between the output and stroke 10 Installation and Handling Mounting Orientation / Installation 11 Application Examples 11 Cylinder Replacement 12 References 12,13
Fig. 11 Removal of rod seal and cushion seal Squeeze the seal from the external circumference to lift one part of the seal, and remove it. Fig 12 How to remove piston seal 3) Tube gasket Take out with the precision screwdriver. 26 - 4-4-3. Grease C a u t i o n Use a specified grease.
Also, if pipe tape is used, as in Fig. (11), leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating air Air supplied to the rotary actuator shall be cleaned by the filter. CRA1 series is lubrication free.
22 1 12 2 13 3 14 4 15 5 16 NBR 6 17 7 18 8 A 19 9 B 20 10 21 11 22 -15- 1 14 2 15 3 16 4 17 5 18 6 19 NBR 7 20 8 21 9 A 22 10 23 11 24 12 25 13 -16- 3. 3.1. 1 I/O LEC-CN5-* / PLC 1 2 DC24V CN5 1 LE-C*-*-* LE-C*-*S-* CN4 CN3 CN2 120.3 120.3 mm mm 200 200 mm/s mm/s 2 100 500 100 500 1 1 200 1000 200 1000 2 2 50 200 50 200
. *3 The travel distance of the actuator per 1 pulse should be 10 [m/pulse]. 11 - LECSC LEFB25 LEFB25U LEFB32 LEFB32U LEFB40 LEFB40U Lead symbol S Series Lead 54 Parameter Para. No.
If a product different from the one ordered is installed, injury or damage can result. -11- 2.5 Operating Environment Warning 1.
(Page 11) 7 1000 fR[N] 100 Lateral load applied to rod 100 80 63 10 50 40 1 0 500 1000 1500 Cylinder stroke [mm] Fig 1. Allowable lateral load applied to rod end C a u t i o n Be certain to align the rod axis with the load and direction of movement when connecting.
Coil 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Terminal no.2 (-) Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm. Note 3) Round or Y-shaped crimped terminal cannot be used.
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (such as the installation of a cover or the restricting of access to the product) to prevent potential danger caused by actuator operation. 11. Do not disassemble the product or make any modifications, including additional machining.
(The first digit of the lower level will start PV flashing.) 11. Press key change 20 to 30. SV 12. Press SEL key to set the value. 13. Press key to return to PV/SV display. SV 313 IDH Series 3.10 Functions and operation of temperature controller IDX-OM-W037 Thermo-dryer 4.
(See Fig.13) Replacement part: Shock absorber Bore size Part no. 32 RB1007-X225 4050 RB1407-X552 Lever Hexagon socket head set screw Push down Fig. 11 10 - Lever Shock absorber 11.Internal construction 12 16 Push down Replacement Grease applied Approx.5mm Fig. 12 Fig.13 20 11 - 32&50 Component Parts (12&50) 12 - Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81
Replace the product in the case of failure such as difficulty removing or inserting tubing. 11 - 5. Construction Male connector Male elbow No.
Maintenance 11 9. Mounting accessories (option) 12 10.
-segments, 7-segments for other) Number of display digits Sub display (right): 5 digits (partially 11-segments, 7-segments for other) Operation light LED is ON when switch output is ON (OUT1, OUT2: Orange) Digital filter 5 Variable from 0 to 30 s/0.01 s increments -79No.PS-OMW0005-C Product No.