LC-OM089xx 20 30 40 50 60 Thread type Metric thread (M5) Rc NPT G Nil N F AL20 Port size Body size Symbol Port size M5 1/8 1/4 3/8 1/2 3/4 1 10 20 30 40 50 60 Note 2) M5 01 02 03 04 06 10 Accessory When more than one specification is required, indicate in alphanumeric order.
OFF: Aulo currenl down lunction olt OFF Half step Fullslep Felease Seftng Aulo current down; Funclion lo automatically reduce 50% Of current output 10 moor when stopped.
*10 *10 *10 *10 *10 *7 For pipe thread type: NPT.
For Flow Control Equipment Precautions, refer to Handling Precautions for SMC Products and the Operation Manual on the SMC website, http://www.smcworld.com Tubing O.D. 6, 8, 10 6 8, 10 8 10, 12 10 12 C values: Sonic conductance dm3/(sbar) Free flow 0.6 1.1 1.2 1.6 2.2 4.2 4.4 Controlled flow 0.7 1.1 1.3 2.2 2.6 4.4 4.8 Free flow 0.2 0.3 0.3 0.2 0.2 0.3 0.3 b values: Critical pressure ratio
Pilot solenoid valve 630 VNH Series High Pressure Coolant Valve 3.5 MPa, 7.0 MPa Dimensions Pg9 Applicable cable O.D. 6 to 8 Pilot EXH port 10(P2) Silencer installed (Standard) EBKX-L7004-040: VNH1, VNH2 AN210-02: VNH3, VNH4 Light/surge voltage suppressor (For DZ) Pilot SUP port 12(P1) Manual override (Non-locking push type) N P2 P1 Main port 1 (Back side port 2) U: Female thread for bracket
Discharge capability -P.9 to 10 8. Troubleshooting P.11 to 12 9. Construction and operating principle -P.13 10. Operating principle P.13 11. Sensor mounting (leakage sensor) P.14 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
P.1320 16 / 17 3. 3-1. 1 2 3 4 5 6 7 8 9 10 3-2. 2040 50100 18 3-2-1. 02 50 3-2-2. 1 6 2 7 6. 7. 3 19 3-2-3. GR-S-010(10g )GR-S-020(20g ) (XC85,X446)P25 1 2 3 4 8 1 100 83(g) L100mm 1 2 1mm 8. 8. g 20 25 32 40 100st 2 3 3 34 50st 0.5 0.5 0.5 1 20 3-2-4. 1) 8, 9 2 ( 8,) 10 3( 8,) 1mm 9. 10. 3-3.
Replace pilot valve assembly. (10) Protect the valve so that water does not splash the coil. (11) To remove foreign matter,air blow piping, then replace valve.
for 8 One-touch fitting for 10 One-touch fitting for 12 VQ30 VQ20 Symbol 2 3 Effective orifice 3.4mm 4.8mm Series VQ20 VQ30 Symbol C6 C8 C10 C12 Switching N.C.
psig (0.0034 to 0.07 MPa) 1 to 30 psig (0.007 to 0.2 MPa) 5 to 100 psig (0.034 to 0.7 MPa) 15 to 200 psig (0.1 to 1.4 MPa) 15 to 300 psig (0.1 to 2.1 MPa) Code No code P 01 02 10 20 30 Connections (Inletq, Outletw) 3) Panel mounting hole: dia. 1.42 inch (36.1 mm).
temperature Cv 3) 0.7 1.3 1.0 2 x 10-11 Pam3/sec 2 x 10-10 Pam3/sec 4) 4 x 10-9 Pam3/sec 4) Ra max 15 in. (0.4 m) Option: 10 in. (0.25 m) Face seal , Tube weld Bottom mount 0.36 in3 (6.0 cm3) 1.27 kg 5) Inboard leakage Outboard leakage Leak rate Across the seat leak Surface finish Connections Installation Internal volume Weight 1/4 turn round knob with open/close indication window 7) 1/4
Power supply A Air-cooled refrigeration Symbol Power supply 10 Single-phase 100 VAC (50/60 Hz) Specications * There are different values from standard specications.
type allows element replacement ZFB30 8, 10, 3/8" 75 Easily replaced filter element ZFB40 1/2" 100 ZFC 10 4, 5/32" ZFA ZFA IN/OUT straight piping ZFC5 In-line type 20 Easy installation and removal with One-touch fittings ZFB ZFB 6, 1/4" 30 ZFC ZFC 5 P.281 Light and compact molded resin parts 8, 5/16" 70 ZFC7 10, 3/8" 80 Easily replaced filter element 12 100 Note) Flow rate when initial
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s 13 Working Principle 1. When air is supplied, it passes through the switching valve and enters drive chamber B. 2.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s Pulsation Attenuating Capacity The process pump generates pulsation because it discharges a liquid using two diaphragms.
Install it above 0.6m from the floor. 9 Maintenance 10 Troubleshooting 6 Operation Continued 6 Operation Continued 9.1 Daily Check 10.1 Alarm list No. Modes Function Selectable Setting Default No.
Node address setting, Communication speed setting 1) Turn on (SW mode) the switch No. 10 of the 10-digit switch mounted on the SI unit. 2) Change the instance attribute value via the network as indicated below.
Symbol 0 P Side 1 E Side Side Bottom (1) Side Other A, B Side 9 Note 1) Size of A, B port bottom ported: Rc 3/8, 1/2 Option Stations Base specifications 2 1 Individual exhaust Common exhaust 02 2 stations 10 10 stations How to Assemble Manifold To order valves and blanking plate assembly mounted onto the manifold, list valves and blanking plate assembly with manifold base part number.