Magnet: None, Mounting: B (Through-hole), Bore Size: 250 (2 1/2"), Stroke: 250 (2 1/2"), Body Option: M (Male Rod End)
Magnet: D (Built-in), Mounting: A (Both Ends Tapped), Overall Length: Z (Super Compact), Bore Size: 250 (2 1/2"), Stroke: 250 (2 1/2")
Magnet: None, Mounting: C (Rear Clevis), Overall Length: Standard, Bore Size: 250 (2 1/2"), Stroke: 250 (2 1/2")
Magnet: None, Mounting: A (Both Ends Tapped), Overall Length: Standard, Bore Size: 250 (2 1/2"), Stroke: 250 (2 1/2")
Magnet: D (Built-in), Mounting: C (Rear Clevis), Overall Length: Standard, Bore Size: 250 (2 1/2"), Stroke: 250 (2 1/2"), Body Option: C (Rubber Bumper), Auto Switch: No Switch, Lead Wire or Prewired Connector: M (1m)
Series: 250 [3 Port COM (Single Unit)], Voltage: 5 (24VDC), Electrical Entry: G (Grommet / Tape winding), Orifice: 2 [250 (3 Port) Ø1.6; 350 (3 Port) Ø2], Port Size: 01 [1/8 (6A)], Thread: Rc, Material: J (Stainless Steel Body, EPDM Seal, Class B Coil), Option: F (Foot Bracket), CE Compliance: Q (CE Marked)
Magnet: None, Mounting: B (Through Hole), Overall Length: Standard, Bore Size: 250 (2 1/2"), Stroke: 250 (2 1/2")
PNP DC Programles Step Controller (LEM), ELECTRIC ACTUATOR, 0.13 lb
PNP DC Programles Step Controller (LEM), ELECTRIC ACTUATOR, 0.13000 lb
PNP DC Programles Step Controller (LEM), ELECTRIC ACTUATOR, 0.13000 lb
LECP1 series is a programless controller capable of setting up an electric actuator operation without using a PC or teaching box. Through the combination of parallel I/O inputs, 14 points of positioning are available. The speed and acceleration of the positioning can be set by the switch for each operating direction. A single signal sent to a dedicated terminal returns an actuator to
Series LECP6 controller has two available modes for the setting software and teaching box. In the easy mode, the operation can be started by only setting the speed, position, etc. Using the normal mode allows a further detailed setup. A few of the main functions of the LECP6 controller are actuator control, specified force operation, separated power supply, and returning the actuator
Series LECP6 controller has two available modes for the setting software and teaching box. In the easy mode, the operation can be started by only setting the speed, position, etc. Using the normal mode allows a further detailed setup. A few of the main functions of the LECP6 controller are actuator control, specified force operation, separated power supply, and returning the actuator
ETHERNET/IP DC CONTROLLER, ELECTRIC ACTUATOR CONTROLLER, N31, 0.21 lb
Linear Guide Double Axis Slider, ELECTRIC ACTUATOR, 4.36 lb
Ethernet/IP Direct Connect, ELECTRIC ACTUATOR CONTROLLER, 0.13 lb
Linear Guide Double Axis Slider, ELECTRIC ACTUATOR, A22, 4.51 lb
EtherNet/IP Direct Connect, ELECTRIC ACTUATOR CONTROLLER, 0.13 lb
EtherNet/IP Direct Connect, ELECTRIC ACTUATOR CONTROLLER, 0.13 lb
Low friction, double acting, single rod, Bore size *: 20, 25, 32, 40, 50, 63, 80, 100, Standard stroke *: 25, 50, 75, 100, 125, 200, 250, 300, Auto switch capable, Variety of lead wires and prewired connectors ROUND BODY CYLINDER. CG1-Z Cylinder, FRANCE SPL. 5.20000 lb. 333.