PF2x5.eng

Caution: 36 to 38 Nm Rc(NPT)1 45 mm PF2W511 Sensor Monitor PF22 Mounting and Installation Wiring WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Black Warning: 1 Main circuit + Installation Brown DC(+) Connections should only be made with the power supply turned off.

Digital Flow Switch (Remote type sensor unit)

Nominal thread size Required torque Rc(NPT)3/8 22 to 24 Nm Rc(NPT)1/2 28 to 30 Nm Rc(NPT)3/4 28 to 30 Nm Rc(NPT)1 36 to 38 Nm Model Width across flats of attachment PF2W504 34 mm PF2W520 PF2W540 PF2W511 45 mm PF2W504T 34 mm PF2W520T PF2W540T -16No.PF-OMO0014-D Wiring Connections should only be made with the power supply turned off.

PF3W7x.eng

Rc(NPT)1 36 to 38 Nm Without temperature sensor/without unit selection function 3. Press the SET button to finish the setting. Rc(NPT)11/4 40 to 42 Nm [ oUt2] Output mode (OUT2) [ HYS] Hysteresis mode Element Description Rc(NPT)11/2 48 to 50 Nm [ 2ot] Switch operation (OUT2) [ 2_P] Normal output The switch turns on within a set flow range (from P1L to P1H) during window comparator mode.

Digital Flow Switch (Manifold type)

Nominal thread size Tightening torque Rc(NPT)3/8 15 to 20 Nm Rc(NPT)1/2 20 to 25 Nm Rc(NPT)3/4 28 to 30 Nm Rc(NPT)1 36 to 38 Nm If the tightening torque is exceeded, the product can be broken. If the correct tightening torque is not applied, the fittings may become loose. Avoid any sealing tape getting inside the piping.

PF3WBCSR.eng

Rc(NPT)1/2 20 to 25 Nm Specifications Rc(NPT)3/4 28 to 30 Nm Rc(NPT)1 36 to 38 Nm After maintenance is complete, perform appropriate functional inspections and leak tests. Stop operation if the equipment does not function properly or there is a leakage of fluid. When leakage occurs from parts other than the piping, the product might be faulty.

PF3W7.eng

Rc(NPT)1 36 to 38 Nm Other parameter settings If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident. Set value P_1 Installation Use the product within the specified operating pressure range and temperature range.

PF3W5.eng

They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 4 Analogue output (flow rate) Rc(NPT)3/4 28 to 30 Nm Pin number of the connector at the body side Rc(NPT)1 36 to 38 Nm Maintenance Rc(NPT)11/4 40 to 42 Nm Element Description Rc(NPT)11/2 48 to 50 Nm How to reset the product after a power cut or when the

PF3W7x-X445.eng

[F30] Storing of accumulated flow OFF [not held] Rc(NPT)1 36 to 38 Nm System error Turn the power off and turn it on again. If the failure cannot be solved, contact SMC for repair. [F80] Setting of power saving mode No setting [display is turned on] Rc(NPT)11/4 40 to 42 Nm Switch ON Switch OFF Do not touch the terminals and connectors while the power is on.

LFE-OMZ0012

Nominal thread size Appropriate tightening torque Rc(NPT)3/8 22 to 24 Nm Rc(NPT)1/2 28 to 30 Nm Rc(NPT)3/4 28 to 30 Nm Rc(NPT)1 36 to 38 Nm If the tightening torque is exceeded, the product can be damaged. If the tightening torque is insufficient, the piping may become loose. The product body is made of resin.

Process Pump

Description PAX112 Diaphragm kit KT-PAX1-31 Check valve kit KT-PAX1-36 Switching valve parts kit KT-PAX1-37#1 Pilot valve kit KT-PA5-38 Pulsation attenuator control valve kit KT-PAX1-39 Piping and Operation Caution Mount the pump so that the reset button faces upward. Air to be supplied to the air supply port should be cleaned and filtered through AF filter, etc.

AXTS-OMY0007

type AXTS040*-3B-X2 External pilot valve Ratio of operating frequency and ON time AXTS040*-3(B)-X2 ON 10 OFF adjustment OFF[] Frequency [Hz] needle [rotation] 7 5 3 1 1 3 5 7 8 0.1 Hz 0.1 Hz 0.1 Hz 0.1 Hz [Hz] 1 6 2% 2% 1% 1% 2.0 Hz 2.3 Hz 2.4 Hz 2.0 Hz ON adjustme nt [Rotation] 4 Number of rotation of ON adjustment needle 3 OFF 29% 17% 15% 14% ON 2 [] 3.7 Hz 4.8 Hz 4.9 Hz 4.8 Hz 5 51% 36%

HRX-OM-Z002

Port size Table 3-7 Piping port size Name Port size Recommended Recommended piping tightening torque specifications Circulating fluid outlet/ return port (CH1) *1 Rc1 36 to 38 Nm 1.0 MPa or more Circulating fluid outlet/ return port (CH1) *2 Rc1/2 28 to 30 Nm 1.0 MPa or more Circulating fluid outlet/ return port (CH2) Rc1/2 28 to 30 Nm 1.0 MPa or more Drain port Rc1/4 8 to 12 Nm Facility

HRX-OM-T004

PV SV 36. Select contact output 3 selected alarm from the table below with [] key or [] key, and confirm by pressing SEL. Table 2.4-19 List of set values Set values Explanation Initial value (Default setting) Setting/checking are not available unless the function setting of contact output 1 is selected alarm status signal. Sets selection alarm.

HRX-OM-R028

PV SV 36. Select contact output 3 selected alarm from the table below with [] key or [] key, and confirm by pressing SEL. Table 2.4-19 List of set values Set values Explanation Initial value (Default setting) Setting/checking are not available unless the function setting of contact output 1 is selected alarm status signal. to Sets selection alarm. Set range is AL.01 to AL.48.

A_HEC-OM-K001

Signal A DC output B DC output C DC output D DC output E DC output F DC output G FG DC connector (HED007-C2* 9.4 Specifications of Connectors 9-11 A_HEC-OM-K001-1.7 Chapter 9 Appendix 3) Signal connector HED003-C2*, HED005-C2*, HED007-C2* DDK: JMR1610FG-36 Connect the signal cable connector of Heat Exchanger. Pin No.

XLC-25,40 ∗ -F7NJ ∗ - ∗ Series

part) 6 (SUS304) Bellows (material: SUS316L) 5 Valve (material: SUS304) () 2 Valve seal (maintenance part) 4 (A6063) C C C C D D D D Body (material: A6063) K C C C C E E E E E E E E KF flange F F F Fn n n n (KF) () Heater (option) Auto switch H H H H J J J J G G G G B B B B A A A A A A A A Model A B C D E Fn G H J K XLC-25 50 120 48 1 12 40 26 39 27.5 8 XLC-40 65 171 66 2 11 55 41 63 36

Return Filter

Fix the width across flats (36) at the bottom of the bowl with a wrench and tighten it to the bowl. (Tightening torque: 20Nm) 5) Restart the operation 1. After the replacement of the element, check the parts are assembled correctly before restarting operation. In case of fluid leakage, stop the operation immediately.

K35-OMW0030

JOG+ JOGPiston rod operation Moves to the retracted end direction OFF ON Retracted end Stops moving ON ON Stop Target position operation (4-20 mA) OFF OFF Retracted end Set point 36 7-2. Calibration The piston rod movement range (set point) can be set when using the Target position operation (refer to 7-3).

Standby E/P Regulator (Air Management System/ELECTRO-PNEUMATIC REGULATOR)

(Page 12) 0x0024 (36) 0 R Device Status N For more details, refer to "Device details status parameter." (Page 12) 0x0025 (37) 1..11 R Detailed Device Status N *1: R means Read and W means Write. *2Y is included in data storage, N is not included in data storage. *3: 8 octets fixed character string. *4: "x" represents a major revision number.

MX-OMP0051

,,, 3-2 18 3-3 1 2 3 4 5 6 7 8 MXQ6(B),8(B,C),12(B,C) 9 Assy MXQ6A,8A,12A, MXQ16(A,B),20(A,B),25(A) 10 (MXQ6(B)) (MXQ8(A,B,C),12(A,B,C)) (MXQ8(A,B,C),12(A,B,C)) 11 (MXQ16(A,B),20(A,B),25(A)) (MXQ16(A,B),20(A,B),25(A)) 12 13 A 14 15 16 17 18 19 (MXQ6A,8A,12A, MXQ16(A,B),20(A,B),25(A)) 20 21 22 O 19 / 23 24 25 26 27 28 / 29 30 31 32 33 34 35 36