Particle generation measurement test classify the 13/22-MXQ as grade 3, 4 which is determined by the type of adjuster option that is selected. After inspection, the 13/22-MXQ is blown with high purity air (clean bench/class M3.5) in a clean environment. It is then sealed and shipped in an anti-static double bag.
Particle generation measurement test classify the 13/22-MXQ as grade 3, 4 which is determined by the type of adjuster option that is selected. After inspection, the 13/22-MXQ is blown with high purity air (clean bench/class M3.5) in a clean environment. It is then sealed and shipped in an anti-static double bag.
IMPACT BLOW GUN, BLOW GUN, J03, 380 lb
EXxx-OMQ0015CN Content 0 10 1 11 2 12 3 13 4 14 5 15 6 16 7 17 Unit diagnostic status 1 7 6 5 4 3 2 1 0 Byte 3 Bit No.
Dimensions for installation n: number of valve stations n L 1 2 3 4 5 6 7 8 L1 120.7 136.7 152.7 168.7 184.7 200.7 216.7 L2 80 96 112 128 144 160 176 n L 9 10 11 12 13 14 15 16 L1 232.7 248.7 264.7 280.7 296.7 312.7 328.7 344.7 L2 192 208 224 240 256 272 288 304 (mm) The above table shows dimensions as an example for the SY5000 series valve manifold.
Precautions for handling When joining six or more units, fix the middle part of the complete unit with an intermediate reinforcing brace to prevent incorrect connection between the units due to deflection. 13 EX## OMS1015-A Wiring Connect the M12 cable. M12 connector is applicable for SPEEDCON connector.
How to Use the Software 13 8.1. The IO-Link Module setting screen 13 8.1.1. Search Master 13 8.1.2. Individual selection 14 8.2. IO-Link Module Setting Screen 15 8.3. Common Screen 15 8.4. Port Config Screen 16 8.4.1. Reading the IO-Link Port Setting 16 8.4.2. Changing the Settings of the IO-Link Ports (Only possible when not connected to PLC) 17 8.4.3.
The buttons cannot be operated. 13 Product failure Replace the product. Rework the piping. If the tightening torque is exceeded, the mounting screws, brackets and the pressure switch may be damaged. Air or liquid leakage Check if air or liquid are leaking from the piping. 14 The product is noisy. Product failure Replace the product.
Display measurement units cannot be changed. : The units selection function is 13 not for use in Japan : Fixed to SI units: L/min Product failure Replace the product. Key-lock mode is activated Check if the key-lock function is turned on. Check the key-lock function. 14 Buttons do not operate. Product failure Replace the product.
Dynamic viscosity [cSt] Viscosity [mPas] Density [g/cm3] 1 [mPas1 [cP] 13 Working Principle 1. When air is supplied, it passes through the switching valve and enters drive chamber B. 2.
Construction and operating principle -P.13 10. Operating principle P.13 11. Sensor mounting (leakage sensor) P.14 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Boards connected after the base are set as remote. 1 2 3 Operating conditions: ON ON OFF Cascade base ON OFF OFF Cascade remote Fig. 13 Base board . Example for cascade connection 1) Setting Cascaded board: 3 pcs.
Boards connected after the base are set as remote. 1 2 3 Operating conditions: ON ON OFF Cascade base ON OFF OFF Cascade remote Fig. 13 Base board . Example for cascade connection 1) Setting Cascaded board: 3 pcs.
(PI control) SV 5.4 Operation of Controller 5-13 A_HEC-OM-J004-4 Chapter 5 Operation <6> Heating proportional frequency setting / Mode indicator: Initial value: 2 sec. Setting range 1 to 120 sec. PV Heating for the proportional frequency setting Indicates that the heating for the proportional frequency setting mode is activated with Indicator .
Period and Scope of Warranty 13 7. Parts Replacement Procedure 14 1 XL-OMS0001-B Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Bit 13 System error 0x1811 Occurs when a system error . Bit 12 Solenoid valve error 0x1812 Occurs when a solenoid valve error . Bit 11 Internal communication error 0x1813 Occurs when an internal communication error . 4 Bit 10 Alarm generation Bit 8~9 of Byte 4 and Bit 7~4 of Byte 5 It is set when any of them is ON, otherwise it is 0.
Therefore, avoid designs where a single load is moved by synchronizing multiple cylinder operations. 12.Do not disassemble the product or make any modifications, including additional machining Doing so may cause human injury and/or an accident. 8 13.
CEU5 13 23m 23m () CEU5 11 AC 10 70500mm/s 12 6-2 5,6, 12 5 5,12 10 ?
No.D-S-OMI0002-C PRODUCT NAME Solid state auto switch MODEL / Series / Product Number D-F6# Series Table of Contents Safety Instructions 2 Model Indication and How to Order 11 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 13 Installation 13 Circuit diagram 14 Troubleshooting 15 Specifications 19 Specifications 19 Dimensions 20 Operating range 21 -1No.D-S-OMI0002
If the kinetic energy of the load exceeds the allowable value, it could damage the product, and cause a hazard to humans and damage the machinery and equipment. (13) Provide a shock absorber if the kinetic energy that is applied to the product exceeds the allowable value.