Possible to transfer a workpiece at low-speed. The rotation angle can be adjusted between 90 and 190. n io r a at n t g o Rotation starting point e R End of rotation DL L R B B L e o g t B a n ti a o r n n o r a ti n a g t Rotation starting point End of rotation o A A e Operating size 20 30 40 Operating size 20 30 40 R A Lmax 15 18 24 27 31.5 Size 10 15 20 30 40 Rotation starting point End of rotation Lmax 24 27 31.5 Lmax 24 27 31.5 Size
Type 20 (5 Port/Body ported) SS5YJ520P 05 A, B port Applicable blanking plate assembly SYJ5000-21-3A A A B A P, R port thread type P port 1/8 B Number of stations A B B 03 3 stations Nil 00F 00N 00T Rc G NPT NPTF : : Applicable connector assembly Refer to page 35. 12 12 stations R port 1/8 Type 41P (5 Port/Base mounted) How to Order SS5YJ541P 05 M5 A A B A, B port M5 x 0.8 A P, R port thread
A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.
A G i 2 x P Port size G A 2 x P Port size b B Conduit DIN terminal D F Q S Cable 6 to 12 G1/2 F Q 280 D G1/2 45 (42) (44) 31.5 Built-in full-wave rectifier type R C C R E J J E 2 x M depth 5 H 2 x M depth 5 B B1 H G A G A B B1 2 x P Port size 2 x P Port size Bracket mounting hole a1 (VXS23, 25) a a1 (VXS24, 26) 6.5 10.5 Dimensions (mm) Model Port size P A B B1 C D E F G H J M Bracket mounting
It is again necessary to connect a contact protection box in order to extend its life. Please contact SMC in this case.
Devise a safe system so that if a person engages the emergency stop, or if a safety device is tripped during a system malfunction such as a power outage, the movement of the cylinder will not cause a hazard to humans or damage the equipment. Avoid synchronized operation using cylinders only.
Do not use this product on board a vehicle or a vessel. This product must not be installed and used on board a conveyance such as a vehicle or a vessel, as it may become damaged due to vibration. If it must be used in such a manner due to unavoidable circumstances, please contact SMC beforehand. 1.
Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
1 (P) (A) 4 (B) 2 3 position exhaust center (A) 4 (B) 2 5 (R1) 3 (R2) 1 (P) 3 position pressure center (A) 4 (B) 2 i 5 (R1) 3 (R2) 1 (P) 5 (R1) 3 (R2) 1 (P) (This figure shows a closed center type.)
Aluminum alloy 1728 3 Port 3 Position Valve VEX3 Series Working Principle Fig. (1) A R Fig. (2) Closed center Fig. (3) P A 3(R) 3(R) 3(R) 2(A) 2(A) 2(A) 1(P) 1(P) 1(P) This is a 3-port switch valve in which the shaft 7 extending from the driving piston 3 opens/closes a pair of poppet valves 6.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
OFF 8 V 4 PNP (C/Q) 0.25 A ( US1 ) 57 No.EX-OMW0014CN-A 9.3.
28.5 29 32.5 23.5 28 28.5 A 34.5 25.5 30 30.5 B 6 6.5 10.5 13.5 16.5 19.5 B 12.5 15.5 18.5 21.5 A 29 29.5 33 24 28.5 29 B 6.5 7 11 14 17 20 A 26 26.5 30 21 25.5 26 B 3.5 4 8 11 14 17 A 19.5 24 24.5 B 9.5 12.5 15.5 A 31.5 22.5 27 27.5 B 9.5 12.5 15.5 18.5 A 35.5 26.5 31 31.5 B 13.5 16.5 19.5 22.5 MK220 MK225 MK232 MK240 MK250 MK263 Auto Switch Mounting Bracket Part No.
Although the circuit at the output side of the switch is surgeprotected, damage may still occur if a voltage surge is applied repeatedly. When a load which generates a surge, such as from a relay or solenoid valve, is directly driven, use a switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications.
1 E-P HYREG Series VY1 A hybrid regulator is created from a regulator and a solenoid valve F.R.L. AV AU Stepless control through electric signals AF A maximum effective area of 670 mm2 (2B) can be covered by the combination of an ultra-compact electro-pneumatic pilot valve (22.4 x 30 x 39) and a 3 port, high-capacity exhaust main regulator (Series VEX100).
If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box. 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 50m or longer.