g (without options) Note 1) Characteristics shown above Supply pressure Output pressure are based on the piping conditions of Fig. 1. 5 MPa Max. 3 MPa This range is outside of the control (output). 0.01 MPa 0 3/8 x 1 m 0 0 1 0 Load Orifice 2 N2 Source Input signal (%F.S.)
T3 Cylinder with Bypass Piping Component Parts T1 81.4 93.3 99.8 T2 63.4 73.8 80.3 T3 57.8 67.8 74.3 TH 47.9 57.3 57.3 TP Rc, NPT, G 1/8 Rc, NPT, G 1/4 Rc, NPT, G 1/4 Description No. 1 2 3 4 Qty. 1 1 1 1 Part no.
Tubing size Tensile force of tubing (N) 3.2, 1/8'' 5 4, 5/32'' 8 6, 1/4'' 12 8, 5/16'' 20 10, 3/8'' 30 12, 1/2'' 35 16 50 7 - Caution (1) Chamfer dimension for female thread of the connection thread Confirming to ISO 16030 (air pressure fluid dynamics connection ports and stud ends), the chamfer dimensions shown below are recommended.
In the case of diodes, the residual voltage is approximately 1 V. Rc 1/8 3 to 5 Rc 1/4 8 to 12 (4) Piping to products When piping to a product, refer to the catalog to avoid mistakes in the position of the supply port, etc. (4) Operation in low temperature conditions It is possible to operate this valve in extreme temperature, as low as 10C.
3 @1 @0 !1 !0 !2 r MHZ w u MHF e MHL !5 MHR y !9 u t MHK Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com MDHR3 !4 !3 MHS q !1 @0 @1 MHC w o MHT e i MHY !5 MHW MRHQ r !7 !6 t !8 !0 !2 i !9 y u Misc.
Confirm that the value is within the operating range of the point of application L = 60mm. Work piece weight (kg) 10 10 5 5 1 1kg 1 0.25kg 0.1 10 20 40 0.1 5 10 20 30 Transfer speed (m/min) Transfer speed (m/min) 32.5m/min 12m/min Procedure3 Confirmation of allowable lateral load MIW12 MIS12 1. Calculation of applied lateral load F F = N m g (N) = 0.2 x 10 x 0.1 x 9.8 = 2.1 (N) 1.
A guide for the additional tightening is 1/6 to 1/4 turns. But in case of the brass sleeve, the limit for additional tightening is 1/2 turns. When there is a leak even after additional tightening, replace the sleeve with new one. (5) Sleeve is not recyclable.
If the leakage volume is 30 /min (ANR), the vacuum pressure of the S type is 20 kPa q w e, and for the L type it is 33 kPa q' w' e'. If the leakage volume is 5 /min (ANR), the vacuum pressure of the S type is 80 kPa r t y, and for the L type it is 47 kPa r' t' y'.
Please contact SMC when disassembly is required.) 3. When replacing seals, take care not to hurt your hand or finger on the corners of parts. 5 - 1.
8 1 8 1 4 1 8 1 4 1 4 3 8 1 2 1 2 3 4 1 2 M5 M5 AMR 1 4 2 1 (5) (5) Weight (kg) 0.15 0.18 0.2 0.3 0.5 1.4 2 4 ITV Note 1) No condensation.
Model no. 1 3 5 A VZ X1 ( ) VZ3 A ( ) Manual override Entry is the same as standard products. Entry is the same as standard products.
~k J Major Dimensions Clamp Cylinder: Series CKS1 3-1/ 4 +Stroke H Speed controller Cushion valve " " .5 ~ ..,.._ . ", 5 ' !
/min (ANR) is under the conditions of 20C, 1 atmospheric pressure and relative humidity of 65%..
Details of each function are explained in section (1-1) to (1-9) below: (1-1) Menu (1-5) STOP button (1-4) Mode selection (1-2) Sub window buttons (1-3) Servo ON / OFF (1-6) Actuator operation status (1-7) Current step data No. (1-8) Communication status (1-9) Time and date (recognised in the connected controller) (1-1) Menu Menu is used to display each kind of window, printing, etc.
However under Japanese regulation, only MPa is available in Japan. 0 600 psig/bar 1) 6 10 20 40 4.1 MPa 7 MPa 14 MPa 28 MPa 1000 psig/bar 1) 2000 psig/bar 1) 4000 psig/bar 1) 1) Under Japanese Measurement Law, this gauge should not be used in Japan.
In the case of diodes, the residual voltage is approximately 1 V. Caution Connection thread size Proper tightening torque (R, NPT) (Nm) 1/8 3 to 5 1/4 8 to 12 4. Piping to products 4. Operation in low temperature conditions When connecting piping to the product, refer to the catalog to avoid mistakes in the position of the supply port, etc. This product is universal porting type.
Port 12 (P1) Port 10 (P2) Working Principle (Vacuum pilot type is excluded) 1 4 1 4 VNB0 , 1 (N.C.) When the pilot solenoid valve u is not energized (or when air is exhausted from the port P1 of the air operated type), the valve element r linked to the piston t is closed by the return spring y.
Back pressure exceeding the set pressure is applied to the outlet. 5. 5. Air leaks Loosened bonnet. Diaphragm is damaged. Fasten the bonnet. Replace the diaphragm assembly. 1. 1. Air leaks between the bonnet and the body. 2. 2. Breakage of bowl seal. Grease up before assembling. Replace the bowl seal. 1. 1. Air leaks between the bowl and the body. (Note 2) Replace the bowl assembly.
Applicable model LVR20 LVR40 LVR50 03 3 x 2 LVR20 LVR40 LVR50 03 1/8" x 0.086" 04 4 x 3 05 3/16" x 1/8" 06 6 x 4 07 1/4" x 5/32" 10 10 x 8 11 3/8" x 1/4" 12 12 x 10 13 1/2" x 3/8" 19 19 x 16 19 3/4" x 5/8" LQ3 Metric size Inch size Symbol Applicable tubing size Applicable model Symbol Applicable tubing O.D.
Limited warranty and Disclaimer 1.The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.