38 58 109 25 to 800 29 14 57 136 39 3/8 11 13 88 14 37 104 40 0.15 0.18 M10 x 1.25 37.5 11 21 10 45 65 118 25 to 800 29 14 57 136 42 3/8 11 13 95 14 36 104 50 M10 x 1.25 45 14 27 10 52 76 145 25 to 800 35 18 60 150 46 1/2 11 18 115 17 43 116 63 M12 x 1.5 50 18 27 10 63 90 165 25 to 800 41 19 71 156 52 1/2 14 20 132 19 43 114 0.20 80 M16 x 1.5 60 18 22 11 80 110 190 25 to 1000 45 20 74 166
DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so.
12/14 21.5 60 32 18 39 4 4 4 4 1 1 43 33.5 24.5 13 17 27 2 x Rc, G (According to ISO1179-1), NPTF 1/2" 1(P) port 2n x Rc, G (According to ISO1179-1), NPTF 3/8" 4(A), 2(B) port (n-1) x 27 64.5 U side D side n Station number 4 2 1 3 L2 45 L1 98 (n-1) x 27 27 56 56 2 Indicator light 21 Manual override 188.5 (3-position) 173 (Double dual 3-port) 157.5 139.5 (Single) 14 14 14 14 131 8 115 12
(ZP)[1][2][8][0]17bit 14 37 14 (5) ON/OFF((DO)) ON/OFF [9][0] (a) DO [8][B][0][0]0004DO 0 0 0 4 4 DO (b) ON/OFF [9][2] [A][0] b31 b 1 b 0 1 ON 0 OFF bit 16 bit CN6 bit CN6 bit CN6 bit CN6 0 14 8 16 24 1 15 9 17 25 2 16 10 18 26 3 11 19 27 4 12 20 28 5 13 21 29 6 14 22 30 7 15 23 31 (c) DO DO[8][B][0][0] [8][B] [0][0] 0 DO 14 38 14 (6) (a) [8][B][0][0]0003 0 0 0 3 3 (b) ([8][B]
Warning (1) Do not disassemble or repair the product.
DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so. DO NOT work inside this product unless you have been trained to do so.
Do not remove the name plate. 13. Perform periodic inspections and confirm normal operation, otherwise it may be impossible to guarantee safety due to unexpected malfunction or erroneous operation. 14. Take great care since the SI Unit side surface of the EX260-SPNl may become hot, causing burn hazard. 15. Do not use in places where there are cyclic temperature changes.
Check the SpeedWork Load Graph (Guide) on pages 14 and 15.
tubing: 6 Applicable tubing: 6 Applicable tubing: 6 Width across flat 14 Width across flat 14 Width across flat 14 2 2 2 2 2 2 7 18 12 12 18 18 12 M12 x 1 M12 x 1 M12 x 1 33.2 33.2 Width across flat 14 Width across flat 14 Width across flat 14 7 5 5 5 7 1.8 1.8 1.8 1 1.2 1.2 10 13 16 11 14 17 9 With Adapter: Vacuum Inlet Series ZP3 Vertical 4 to 8 Pad diameter Vertical Dimensions/With Adapter
NBR 14 Holding rubber Parts list No.
Do NOT make upward piping. 2. Float type auto-drain (N.C.) DO NOT pipe upwards. (ANR)}. 2) Set pressure more than 0.1 MPa. 2. Float type auto-drain (N.C.) 1) Compressor can be used even if energy is under 3.7 kw. 2) Set pressure more than 0.15 MP 14-3-14 1 Pilot Operated Regulator Series AR425 to 935 Standard Specifications F.R.L.
14 14 14 14 14 14 D side U side For the I/O Unit part number mounted, refer to the following pages.
It will cause failure of the controller or its peripheral devices. 14. Do not use the product in an environment subject to a temperature cycle. It will cause failure of the controller or its peripheral devices. 15. Do not use the product in a place where surges are generated.
17 14 17 19 14 17 19 17 19 Connection thread 4 14 11 13 15 11 13 14 14 15 13.1 10.4 17 12 6 1 8 1 4 3 8 1 4 3 8 1 4 3 8 1 2 3 8 1 2 26.1 18.0 14 8 18.5 KQ2F16 Applicable tubing 17 41.5 29.5 21 10 Connection thread 19 14 12 58.3 46.1 22 19 18 15 19 24 81 (81) 113 (96) 24 25.7 16 24 25 Note 1) D2: Max. diameter Note 2) ( ): Values for soft nylon 15-2-14 6 One-touch Fittings Series KQ2
14 15 14 14 17 16 18 D-Y59/Y69 D-Y7P/Y7V D-Y7W/Y7WV 8 7 5.5 6.5 6.5 Since this is a guideline including hysteresis, not meant to be guaranteed.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s or more) while handling. Even if the switch body is not damaged, there may be internal damage and possible malfunction. 2. Do not carry an actuator by the auto switch lead wires. Never carry an actuator by its auto switch lead wires.
14 14 14 14 14 14 D side U side For the I/O Unit part number mounted, refer to the following pages.
13 13 14 15 16 14 14 17 18 D-Y59/Y69 D-Y7P/Y7V D-Y7W/Y7WV 8 7 5.5 6.5 6.5 Since this is a guideline including hysteresis, not meant to be guaranteed.
Do not use the product in an environment subjected to cyclic temperature changes. It will cause failure of the controller or its peripheral devices. 14. Do not use in a location where surges are generated.