Actuation: 1 (Single Type), Body: 3 (Body Ported, Manifold), Option: W (For Large Flow, Vacuum), Voltage: 5 (24 VDC), Electrical Entry: M (M Plug Connector, w/Lead Wire; with Light/Surge Voltage Suppressor), Port Size: M5
HRX-OM-X071 Use M5,M6 screws (bolts) or equivalent to the fix the product. Do not drag this product after mounting, as the feet may be damaged. (option -Y) 2. In the case of air cooling type, this product sucks air from the front and discharges it to the back. Please do not block the suction and the discharge air. Please do not install in a sealed place.
Remove these screws Remove these screws Fig. 3-2 Foot mounting screws 2) Then tighten M5 screws (bolts) or equivalent into 4 holes sized to 7mm on the parts marked with arrow for mounting.
:l EgLr oA50, 54 6$ lu8f.2l 1tLJ Bore size ds2iRSf Qi:a 32lln D 1-05 5l!
(P3 P2) x 9.9 V [L] = (Q Qb/2) x (Tc x K/60) Obtain the tank capacity V. (841 600/2) x (0.5 x 2/60) V = = 4.6 [L] (1.0 0.8) x 9.9 Applicable combination model Internal capacity Tank model VBAT05A(1) VBAT05S(1) VBAT10A(1) VBAT10S(1) VBAT20A(1) VBAT20S(1) VBAT38A(1) VBAT38S(1) 5L VBA10A/11A Select the tank capacity over V.
Right angle, 5 m With mounting screw 2 pcs. 807 Series ISA2 DIN Rail ISA-5L Applicable models L 4.5 8 1.25 7.5 Part no.
M4 5 M4 5L Bracket B Bracket A or D Bracket A or D Safety Instructions [ Window comparator mode ] The Pressure switch turns on within a set pressure range (from P1L to P1H) during window comparator mode. Set P1L (switch lower limit) and P1H (switch upper limit) using the setting procedure above.
:l EgLr oA50, 54 6$ lu8f.2l 1tLJ Bore size ds2iRSf Qi:a 32lln D 1-05 5l!
Black OUT1 24VDC Analog output 2 1 Load White Connector pin numbers Load Blue Pin description Pin no. 68 69 DC (+) 1 PFA7H-(-M) Analog output 2 DC () 3 Accumulated pulse output wiring examples OUT1 4 4-I thread depth J 40 Max. 30V 80mA or less OUT1 Black Load ON H OFF Blue 50msec PFA7H-(-M) 28 29 B C D E F G H I J A Model Brown PFA703H PFA706H PFA712H 55 160 40 92 67 55 Rc 1, NPT 1, G 1 36 M5
Qi '5 0 ~ 5l :r 0. 31<.-t-~-+---="I--;;::'--t-t_1 Q. 0.15 f-t.,---+t--t-+---1--+-t--t-l 8Tightening torque of mounting screw (M3) for gauge is 3-Skgf . cm.
Usage 2 x 3 CK-P04 Knuckle pin Clevis pin 4 4 57 Note) Cotter pins and flat washers are attached to the pin as a standard. 430 CK1 Series Options Limit Switch Mounting Base/Dog Fitting 50 75 Material: Rolled steel 4 x M5 x 0.8 17.3 58.7 5 30.2 Part no.
Mounting with bracket Mount the bracket on the body with two M3 x 5L mounting screws. Tighten the bracket mounting screws at a tightening torque of 0.5 to 0.7 Nm. Lever 2. Connector pin numbers for power supply/output cable M3 x 5L DC(+) Brown 5 OUT1 Black 4 Bracket (Part no. ZS-28-B) OUT2 White 3 Analog or auto shift Gray 2 DC(-) Blue 1 M3 x 5L 2.
Mounting with bracket Mount the bracket on the body with two M3 x 5L mounting screws. Tighten the bracket mounting screws at a tightening torque of 0.5 to 0.7 Nm. Lever 2. Connector pin numbers for power supply/output M3 x 5L DC (+) Brown 5 OUT1 Black 4 Bracket (Part no. ZS-28-B) OUT2 White 3 Analog or auto shift Gray 2 M3 x 5L DC () Blue 1 2.
Note 4) An appropriate range is from 3 to 5L/min. To prevent damage to the radiating system, do not supply a flow over the maximum flow rate of 8L/min.
[mm] Bar length [mm] 160 220 340 400 460 580 640 820 1120 1300 1600 1900 2320 2500 4H/4L 4 6H/6L 6 8H/8L 8 AH/AL 10 5H/5L 3/16 7H/7L 1/4 9H/9L 5/16 BH/BL 3/8 : With piping on one side : With piping on both sides : Unrecommended piping Symbol High-voltage cable length [m] 1 1 2 2 3 3 The number of high-voltage cable holders differs depending on the high-voltage cable length.
L[]Z[]5L 280 L[]Z[]3M 640 L[]Z[]5M 850 L[]Z[]3 200 does not start or operation stops suddenly. Perform inspection before/after operation Note. Refer shorter data from above. Energizing tim e Inspection item What to inspect moving range. Reference of travel depending lead Mounting the body No loose part. Check item What to check Motor If it is too hot.
Panel mount adapter ZS-46-B Panel mount adapter + Front protective cover ZS-46-D Front protective cover ZS-27-01 Lead wire with connector ZS-46-5L 5-wire, 2 m Connector for sensor lead wire ZS-28-C -8No.PS-OMW0014-B Summary of Product parts Names of individual parts Operation light: Displays the switch operating condition.
Remarks Sensor connector (For PFMB) ZS-28-C-1 Sensor connector (For PFMC and PF3A7) ZS-28-CA-4 Bracket A ZS-46-A1 Self tapping screws: Nominal size 3 x 8L (2 pcs) Bracket B ZS-46-A2 Self tapping screws: Nominal size 3 x 8L (2 pcs) Panel mount adapter ZS-46-B Panel mount adapter + Front protective cover ZS-46-D Lead wire with connector ZS-46-5L 5 cores, 2 m Front protective cover ZS-27-01
Stop Ensure that the circulating fluid flow is 5l/min.or more. Check the heat load are within the specified range. AL06 High circulating fluid discharge pressure Stop Check the user's piping for bends, squash and foreign matters. AL07 Abnormal pump operation Stop Restart and check the pump is operating.
Stop Ensure that the circulating fluid flow is 5l/min.or more. Check the heat load are within the specified range. AL06 High circulating fluid discharge pressure Stop Check the user's piping for bends, squash and foreign matters. AL07 Abnormal pump operation Stop Restart and check the pump is operating.