<br>Keep in mind that the holding torque at the rotation end is half the effective torque.<br><br>(CRJ series mini rotary actuators have a construction in which backlash does not occur at the rotation end even with the single rack type.)See the video below for details.

<br><br>Note) The start of production dates of the new auto drains (slightly different depending on model) are as follows: <br>IDF1 to 2E and IDF/IDU3E to 37E: March 2019 <br>IDF/IDU55E to 75E: June 2019 <br>IDH4 and IDH6: March 2019<br><br>

<br><br>The main differences/similarities between old AR and AR-A series regulators are as follows. ① The set pressure range differs.

<br><br>FEP (a copolymer of tetrafluoroethylene and hexafluoridepropylene) <br>It has almost the same chemical resistance as PTFE. <br>Since the melting point is about 260°C, which is lower than PTFE or PFA, the highest operating temperature is 200°C. <br><br>PTFE (tetrafluoroethylene resin) <br>Molding is done by sintering.

<br><br>High-temperature specification: the AS□-□-H can be used from -5°C to 80°C.<br>Ex.) AS2000-□-H, AS3000-□-H, AS4000-□-H, AS420-□-H, AS500-06-H, AS600-10-H, etc. <br><br>Low-temperature specification: the AS-□-L can be used from -30°C to 60°C.<br>Ex.) AS3000-□-L, AS4000-□-L, AS5000-□-L, AS420--L, AS500-06-L, AS600-10-L-, etc.

<br><br> <br><br>For the KNS-□ low-noise nozzle with a male thread and the KNS-R01-□ low-noise nozzle with a self-align fitting, the effective area for the nozzle diameter is not available. <br>As the hole sizes are the same, refer to the values below. Ex.) For the KNS-08-100-04, refer to the value for the KNS-R02-100-4.

<br>To avoid such dangers, HRS100/150 series thermo-chillers can be set to continue or stop operation at the time of alarm generation. <br>The default setting for alarm code “AL09” is to stop operation safely (Note 3). <br>If this function has been activated, check the following. <br>① Check whether the level gauge on the tank is below the “Low” level.

<br><br>

<br><br>Note 2) MY1H10 series cylinders support strokes from 60 mm in 10 mm increments for the standard part numbers.<br><br>Refer to the MY series catalog for details.<br>The MY□ series catalog can be found here.

<br><br>The MGG series catalog can be found here.<br>FAQ about the part number when replacing an MGG series cylinder for drivingcan be found here .

<br><br><br><br>

<br>Calculation formula:<br>W = P x S x 0.1 x 1/t<br>(W: Lifting force(N), P: Vacuum pressure(Kpa), S: Area of the pad(cm²), and t: Safety factor of 4 or more for horizontal lifting and 8 or more for vertical lifting) <br>Theoretical lifting force table:<br>The theoretical lifting force can be found using the pad diameter and vacuum pressure.

<br>Flat pads: For flat and even-surfaced workpieces<br>Flat pads with ribs: For workpieces that are easily deformed or workpieces that need to be released reliably<br>Deep pads: For curved workpieces <br>Bellows pads: For when there is no space to install a buffer or for workpieces with an inclined adsorption surface<br>Oval pads: For when you want to reliably perform positioning of long

<br><br>The main differences/similarities between old AW and AW-A series filter regulators are as follows. ① The set pressure range differs.

<br><br> T/TS and TIA/TISA series (soft) nylon tubing <br>TU series polyurethane tubing<br>TUZ series wear-resistant tubing<br>TRS, TRB, TRBU, and TRTU series flame-resistant tubing <br>TPS and TPH series clean tubing<br>TL/TIL, TLM/TILM, TH/TIH, TD/TID, and TQ series fluoropolymer tubing<br><br>The max. operating pressure varies depending on the operating temperature of each series.

<br><br>VEX1□0□ series regulator valves (3-port large exhaust capacity regulator valves)<br>・An external pilot solenoid type and an air operated type are available.・The pressure can be controlled remotely, and pipes of up to 2 inches are supported.<br><br> https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=directional-control-valves&fa_id=10039