<br>Flat pads: For flat and even-surfaced workpieces<br>Flat pads with ribs: For workpieces that are easily deformed or workpieces that need to be released reliably<br>Deep pads: For curved workpieces <br>Bellows pads: For when there is no space to install a buffer or for workpieces with an inclined adsorption surface<br>Oval pads: For when you want to reliably perform positioning of long
<br><br>The main differences/similarities between old AW and AW-A series filter regulators are as follows. ① The set pressure range differs.
<br><br> T/TS and TIA/TISA series (soft) nylon tubing <br>TU series polyurethane tubing<br>TUZ series wear-resistant tubing<br>TRS, TRB, TRBU, and TRTU series flame-resistant tubing <br>TPS and TPH series clean tubing<br>TL/TIL, TLM/TILM, TH/TIH, TD/TID, and TQ series fluoropolymer tubing<br><br>The max. operating pressure varies depending on the operating temperature of each series.
<br><br>VEX1□0□ series regulator valves (3-port large exhaust capacity regulator valves)<br>・An external pilot solenoid type and an air operated type are available.・The pressure can be controlled remotely, and pipes of up to 2 inches are supported.<br><br> https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=directional-control-valves&fa_id=10039
<br>Plug-in type SY3000/5000/7000 series part numbers: SYS□□00, SY□□30, SY□□01, and SY□□31 <br>Existing SY3000/5000/7000/9000 series part numbers: SY□□20, SY□□40, and SY□□45<br><br>The part numbers of the gasket assemblies for use between the plug-in type SY3000/5000/7000 series valves and manifold are as follows.
<br>7) Type H has been standardized for the magnetic holding force.<br>8) There is no longer a separate part number for the type with a switch rail (the old CDY1S) due to the standardization of the switch rail.<br>9) There is no seal kit interchangeability.
<br>Do not forget to reset the knob when restarting operation.<br>MGP series catalog can be found here.<br><br>
The MXQ series includes the following series: <br>① The MXQ□A (double ported type) <br>② The MXQ□B (low thrust with high rigidity type) <br>③ The MXQ□C (single side ported type) <br>④ The MXQ□ (height interchangeable type) released in 2012 <br>⑤ The existing MXQ□<br>The difference between the part numbers of existing MXQ□ and MXQ□ series height interchangeable type cylinders is that a “Z□
<br>For further details, refer to the excerpts from the MWB series “Specific Product Precautions” below.<br><br>
<br>JXC91: Chapter 4, 4-1, Initial setting method<br>JXC92: Chapter 5, 5-1, Initial setting method<br>JXC93: Chapter 5, 5-1, Initial setting method<br>The JXC91, JXC92, and JXC93 series operation manuals can be found here.
<br>Be sure to install a vacuum filter on the vacuum side.<br>② Check that the supply pressure to the ZH has not decreased.
<br>4) Inlet air temperature: °C<br>5) Allowable pressure drop: MPa (The upstream filter, etc., must also be considered.)<br>6) Compressed air supply capacity: L/min (ANR)
<br>The part names in the exploded view are as follows: <br>⑩ Square embedded type pressure gauge (Rc, pressure range 0 to 1.0 MPa): GC3-10AS <br>⑬ Pressure gauge adapter assembly (Rc): ARP20P-310AS-01 <br>⑭ Plug assembly (Rc): ARP20P-320AS-01 <br>⑯ Blanking plate assembly: AR20P-250AS <br>Note) Contact SMC for details on replacement with a digital pressure switch or a digital pressure switch
<br>The main target objects of such lubrication are bearings, chains, cutting machines, presses, etc. <br><br>The AL40 is a full-weight lubricator. <br>This product supplies all the generated oil mist to the outlet side. It passes through the inner walls of the piping and lubricates the target objects.
<br><br>AD402(-A) series auto drains are used mainly to treat drainage from small compressors, air tanks, aftercoolers, and refrigerated air dryers. <br>The max. operating pressure is 1.0 MPa. The product is also suitable for use on the downstream side of a pneumatic line.
<br>Details on specifications other than those shown below can be found on the page of each of tubing series. Reinforced corrugated cardboard <br><br>specification/Longer length reel: T-X64 and https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=tubing&fa_id=11114
<br><br>Speed controllers are mounted on an actuator (cylinder, etc.) and are used to control the speed of the actuator. <br>The internal construction uses a lip seal as a check valve, and it is only able to adjust the flow rate in 1 direction. <br>Throttle valves (Restrictors?) are used to control the flow rate in the piping.
<br>You can set a value between 1 and 999 seconds (there is also a separate continuous mode).<br>There are 2 trigger input methods: continuous input and one-shot input.<br>When you want to set the operation time by the trigger signal length, you can use continuous input.
<br><br>An auto switch cannot be retrofitted when a magnet is not mounted on the piston part (e.g., XLA-40-2 and XLA-40H5-2).
<br>If the contents on the label cannot be confirmed, select the element part number based on the FGD series model. <br>For the FGD□A: Element length L250 (1 piece) <br>For the FGD□B: Element length L250 (2 pieces) or L500 (1 piece) <br>The elements that can be selected for L500 of the FGD□B are sintered metal (EB200 or ES200) and paper (EP200).