MGP -XB13 4 Low Speed Cylinder Specifications M L Stroke MGP XB13 Bore size MGPM, MGPL Applicable series Slide bearing, Ball bushing Bearing type Low speed cylinder 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 Cylinder bore size (mm) 5 to 50mm/s (0.2 to 2 in/s) Piston speed Operates smoothly, without sticking and slipping, at drive speeds as low as 5 to 50mm/s.
Symbol 2 Low speed [0.3 to 2.0 inch/s (7 to 50 mm/s)] specification XB13 XB13 Bore size NCY3B Bore size Stroke Low speed [0.3 to 2.0 inch/s (7 to 50 mm/s)] specifications There is no sticking and slipping even at very low drive speeds of 0.3 to 2.0 inch/s (7 to 50 mm/s). Furthermore, there is no lurching at start-up, allowing smooth drive through the entire stroke.
Cold resistant (40 to 70C) -XB7 CQM -XB9 Low speed (10 to 50 mm/s) -XB13 Low speed (5 to 50 mm/s) MU -XC19 Intermediate stroke (5 mm spacer) Auto Switch Mounting Position -XC22 Fluororubber seals For the auto switch mounting position of CDU long stroke series, refer to page 488, since specifications are the same as standard type, double acting, single rod type.
Toxic gas may be released when you smoke with the grease residue left on your hands, causing a health hazard. 3 -XB13 Low-speed cylinder (5 to 50mm/s) Specifications CXS XB13 Bore size Stroke Auto switch CXSM Slide bearing CXSL Series Bearing type Ball bushing bearing Low-speed cylinder 6, 10, 15, 20, 25, 32 Bore size (mm) 5 to 50mm/s Piston speed This cylinder operates smoothly with minimal
Note 2) Consult with SMC when units are used at a low speed (10 mm/s or faster) (when intermediate stops are not required) since -XB13 (Low speed specification) is available. Note 3) When using the air-hydro type, use the double side hydro unit.
MGP Series (Basic Type), Stroke Variations Stroke [mm] Bore size [mm] Bearing type Made to Order 10 20 25 30 40 50 75 100 125 150 175 200 250 300 350 400 12 -XA: Change of guide rod end shape -XB6: Heat resistant cylinder (10 to 150C) -XB10: Intermediate stroke (Using exclusive body) -XB13: Low speed cylinder (5 to 50 mm/s) -XC6: Made of stainless steel -XC8: Adjustable stroke cylinder/ Adjustable
Symbol Low-speed Cylinder (5 to 50 mm/s) -XB13 Even if driving at lower speeds 5 to 50 mm/s, there would be no stick-slip phenomenon and it can run smoothly.
V V V V V V V V V CM2l R V Water resistant V V v v CM2lX Low speed cylinder V CM2lM Cylinder with stable lubrication function (Lube-retainer) V v v v XB6 Heat resistant cylinder (10 to 150C) Note 1) 20 to 40 v v XB7 Cold resistant cylinder (40 to 70C) Note 1) v v v v v v v v XB9 Low speed cylinder (10 to 50 mm/s) v v v v v v v XB12 External stainless steel cylinder Note 7) v v v v v XB13
Note 2) Consult with SMC when units are used at a low speed (10 mm/s or faster) (when intermediate stops are not required) since -XB13 (Low speed specification) is available. Note 3) When using the air-hydro type, use the double side hydro unit.
Symbol Specifications -XAl Change of rod end shape -XB6 Heat resistant cylinder (10 to 150C) * Not available with switch & with air cushion -XB7 Cold resistant cylinder (40 to 70C) * Not available with switch & with air cushion -XB9 Low speed cylinder (10 to 50 mm/s) * Not available with air cushion -XB13*3 Low speed cylinder (5 to 50 mm/s) * Not available with air cushion -XC3 Special port
25 Standard Standard D Built-in magnet CQS-M Rod end male thread CQS-C With rubber bumper CQS-F 12 to 25 With boss on head end LF G CQS Foot, Flange CQSD Double clevis style 10-, 11Clean series 20Copper and Fluorine-free XB6 Heat-resistant cylinder (10 to 150 C) XB7 Cold-resistant cylinder (40 to 70 C) XB9 Low-speed cylinder (5 to 50 mm/s) XB10 Intermediate stroke (Using exclusive body) XB13
(e.g. combination between 20and -XB9 (-XB13)) In order to avoid such a non-conformity, we distinguish the model no. from the one for standard products by prefixing 20-. Stroke (mm) Maximum Load Mass When the cylinder is mounted as shown in the diagrams below, the maximum load mass W should not exceed the values illustrated in the graph immediately following the diagrams.
Double acting Single rod Double rod Cushion Rubber Air Air Applicable bore size Specification Symbol 32 to 100 125 32 to 100 125 32 to 100 125 Standard Standard Long st Long stroke D Built-in magnet J K MBWith rod boot 32 to 125 10Clean series 20Copper and Fluorine-free R V MB Water resistant XA Change of rod end shape XB5 Oversized rod cylinder XB6 Heat-resistant cylinder (10 to 150C) XB13
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
Magnet: Built-in, Mounting: Double Clevis, Cushion: Rubber Bumper, Bore Size: 2 1/2", Stroke A: 12", +: None, Stroke B: None, Stroke Adjustment: None, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 5m, Number: 2 pcs. (Or None in the Case of No Switch), Stroke Options: Low Speed; 5 to 50mm/s
Magnet: Built-in, Mounting: Foot, Cushion: Rubber Bumper, Bore Size: 1 1/2", Stroke A: 12", +: None, Stroke B: None, Stroke Adjustment: None, Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 0.5m Cord Length, M8-3 Pin Connector, Number: 2 pcs. (Or None in the Case of No Switch), Stroke Options: Low Speed; 5 to 50mm/s