Multi-Axis Step Motor Controller Arbitrary address Vendor ID 7 h (SMC Corporation) Product type 2 Bh (Generic Device) Product code DEh Serial communication USB2.0 (Full Speed 12 Mbps) Memory Flash-ROM LED indicator PWR, RUN, USB, ALM, NS, MS, L/A, 100 Lock control Forced-lock release terminal *4 Communication Cable length Actuator cable: 20 m or less Cooling system Natural air cooling Operating temperature range 0C to 40C
Display panel 50,000 hours (approx. 5 years) End life of backlight of LCD. 183 Series HED Applicable Fluids Chemical CompatibilityTable against the Wetted Parts Material in Chemical Thermo-con Chemical Operating temperature range Compatibility Concentration p Note 2) 50 to 104 F(10 to 40C) Hydrofluoric acid HF: 10% or less p Note 2) 50 to 104 F(10 to 40C) Buffered hydrogen fluoride HF: 10%
Use the air dryer with an ambient temperature lower than 104F (40C). Avoid installation on machines for transporting, such as trucks, ships, etc.
The base oil of grease in the cylinder may seep out of the tube, cover, or crimped part depending on the operating conditions (ambient temperature 40C or more, pressurized condition, low frequency operation). CS1 Releasing the Lock Warning CS2 1.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, SLIDE TABLE, REVERSIBLE, ACTUATOR, MXQ GUIDED CYLINDER, CE, 6MM MXQ DBL-ACT AUTO-SW, .60626 lb
AL09 FLT 55C AL10 OFF *1 40C 3 CH1 Hgih Temp. AL11 CH1 Low Temp. OFF *1 10C 3 Check the effect of ambient temperature. Please review the setting value. There may be causes such as large load fluctuation and flow rate fluctuation. Please review the setting value. AL12 CH1 TEMP READY ALARM OFF *1 +1/-1C 3 CH2 High Temp.
Power supply 200/230V : 40C Installation of multiple products Keep sufficient space between products so that the air vented from one product will not be taken in by other products.
HRX-OM-I051 Chapter 8 Appendix Specification for fluorinated fluid (wide temperature) Table 8-3 Specification for Fluorinated Fluid (Wide Temperature) Model HRZ002-W HRZ008-W Cooling method Water cooled refrigerant Cooling capacity*1 (50Hz/60Hz) kW 2.0 (At 20C) 8.0 (At 20C) Operating temperature range C -20 to 90 Temperature stability C 0.1*2 Galden HT135*3 FluorinertTM FC-3283*3 (-20 to 40C
Pressure 0.7 MPa Pressure Internal Grip Pressure 0.7 MPa Pressure 0.7 MPa 20 0.6 MPa 0.6 MPa 200 MHZA2, MHZ2, MHZL2 0.6 MPa 0.6 MPa Gripping force (N) Gripping force (N) 15 0.5 MPa 0.5 MPa 0.5 MPa 0.5 MPa 150 0.4 MPa 0.4 MPa 0.4 MPa 0.35 MPa 0.4 MPa 0.35 MPa 10 100 0.3 MPa 0.3 MPa 5 50 L 0 10 20 30 40 50 0 20 40 60 80 100 Gripping point L (mm) Gripping point L (mm) MHZ2-16C/MHZL2-16C MHZ2-40C
Note) 20 Min. bending radius mm Min. bending radius mm 10 15 27 35 75 60 48 36 24 25 13 20 to 60C, With water: 0 to 40C (with no freezing) 100 20 to 60C, With water: 0 to 40C (with no freezing) Operating temperature Operating temperature Polyurethane Material Material Nylon 12 Note) Best Pneumatics No.4, page 2.4-1 Note) Best Pneumatics No.4, page 2.4-3 20m roll O.D. I.D.
Pressure 0.7 MPa Pressure Internal Grip Pressure 0.7 MPa Pressure 0.7 MPa 20 0.6 MPa 0.6 MPa 200 MHZA2, MHZ2, MHZL2 0.6 MPa 0.6 MPa Gripping force (N) Gripping force (N) 15 0.5 MPa 0.5 MPa 0.5 MPa 0.5 MPa 150 0.4 MPa 0.4 MPa 0.4 MPa 0.35 MPa 0.4 MPa 0.35 MPa 10 100 0.3 MPa 0.3 MPa 5 50 L 0 10 20 30 40 50 0 20 40 60 80 100 Gripping point L (mm) Gripping point L (mm) MHZ2-16C/MHZL2-16C MHZ2-40C
Pressure 0.7 MPa Pressure Internal Grip Pressure 0.7 MPa Pressure 0.7 MPa 20 0.6 MPa 0.6 MPa 200 MHZA2, MHZ2, MHZL2 0.6 MPa 0.6 MPa Gripping force (N) Gripping force (N) 15 0.5 MPa 0.5 MPa 0.5 MPa 0.5 MPa 150 0.4 MPa 0.4 MPa 0.4 MPa 0.35 MPa 0.4 MPa 0.35 MPa 10 100 0.3 MPa 0.3 MPa 5 50 L 0 10 20 30 40 50 0 20 40 60 80 100 Gripping point L (mm) Gripping point L (mm) MHZ2-16C/MHZL2-16C MHZ2-40C
Valve open Valve open IDFS6E to 11E IDUS3E to 6E Use the air dryer with an ambient temperature lower than 40C. When installing air piping at the air inlet/outlet of air dryer, the IN/OUT port's fitting of air dryer must be held firmly in place with a wrench. Variation of operating conditions may cause condensate to form on the surface of the outlet piping.
Store away from direct sunlight at 40C or less. 2. Open the inner package of double packaging in a clean room or other clean environment. 12 to 14 R 1/4 22 to 24 R 3/8 28 to 30 R 1/2 Mounting 3. Tightening tools Tighten with an appropriate wrench using the hexagon wrench flats on the body. Position the wrench on the base as close as possible to the threads.
Evaluation criteria for ozone resistance SMC's evaluation criteria for ozone resistance in its products can be defined as follows: Products meeting a 5-year (or 43,800 hours) resistance rating (or equivalent) under working conditions that include 40C ambient and fluid temperatures and an ozone concentration of 0.03ppm in 0.5MPa compressed air.
Min. bending radius (mm)(2) 10 15 20 27 35 10 Operating temperature 0 to 40C Burst Pressure Characteristics Curve Conductive polyurethane Material 104 to 107 Surface resistance Note1) Refer to burst pressure characteristics curve for other temperatures. Avoid abnormal temperature rises. Note2) The value at temperature of 20C.
Store away from direct sunlight at 40C or less. 2. Open the inner package of double packaging in a clean room or other clean environment. 12 to 14 R 1/4 22 to 24 R 3/8 28 to 30 R 1/2 Mounting 3. Tightening tools Tighten with an appropriate wrench using the hexagon wrench flats on the body. Position the wrench on the base as close as possible to the threads.
Store away from direct sunlight at 40C or less. 2. Open the inner package of double packaging in a clean room or other clean environment. 12 to 14 R 1/4 22 to 24 R 3/8 28 to 30 R 1/2 3. Tightening tools Tighten with an appropriate wrench using the hexagon wrench flats on the body. Position the wrench on the base as close as possible to the threads.
OUT Standard specification Option Note) Water (Standard, up to 40C) Air (Standard, Dry) Turbine oil Vacuum (up to 1.3 x102 Pa) Carbon dioxide (CO2), Nitrogen gas (N2) Vacuum (up to 1.3 x101 Pa) (V, M) Non-leak (106 Pa m3/s or less) (V, M) IN N.O.
Next, pour water at 5 to 40C, then measure the flow rate with a pressure difference of 0.075 MPa. However, the pressure difference needs to be set with a large enough difference so that the Reynolds number does not go below a range of 4 x 104. By substituting the measurement results for formula (8) to figure out Av.