CQSY/CQ2Y/CM2Y/CG1Y/CA2Y CE1 CE2 Pressure can be controlled regardless of its direction.
Optional wall or panel mounting brackets may also be specified as required. Any standard Coast Series 20, 30, 50, or 70 Series solenoid valve can be mated to the splice box, which will be UL listed for use with UL listed valves.
This silencer can be quickly mounted on the manifold's E (exhaust) port.
Gasket 6 cannot be repaired. Seal kit includes !9, @0, @1. Order the seal kit, based on each bore size. Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g) 60
The IP67 protection can be achieved when it is mounted on a manifold.
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it.
*The auto switch mounting bracket material is also restricted. *2 The D-A90L-900 cannot be mounted on the RSH, RS1H, MY1B25 to 63, CDNA50. *3 The D-M9BW(V)-900 cannot be mounted on the MY1B50. *4 Reed switches (D-A90L-900 and D-Z80L-900) cannot be mounted on the MHZJ, MHZL, MHS, MHL series.
Be sure to connect the pipe to the fluid release port so that fluid releasing work can be absolutely performed. 7. Pipe so that air releasing work can be absolutely performed. The air releasing work can be done firmly if you make the piping in order to flow a small flow constantly into a tank by resin tubing, etc. from the air release valve. (Refer to Fig. 2.)
The fitting and tubing should be provided separately by the customer.
The grease to be applied is available as grease pack. When the grease pack is required, order it using the part number shown below. Grease pack part number: GR-S-010 (10 g) ( The grease to be applied is the same as that used for the cylinder.) Similarly, be careful not to remove the grease from the piston rod end of the built-in shock absorber.
Note) It may be difficult to replace the cushion seal #5. Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed. Grease pack part no.: GR-S-010 (10 g) Piston seal NBR Scraper NBR O-ring NBR O-ring NBR Cushion seal NBR 170
Bore sizes 50mm and larger can be difficult to disassemble. Contact SMC when disassembly/repair is required on the larger sizes. See page 44 for more information regarding seal replacement.Note) A grease pack (GR-R-010, 10g) is included in seal kits.
Contents Bore size (mm) REAR20-PS 20 25 32 40 REAR20-PS REAR25-PS REAR32-PS REAR40-PS @0 @1 @2 @3 @4 @5 26 Cylinder tube gasket NBR REAR32-PS REAR25-PS Set of left nos. @0, @1, @2, @3, @4, @5, #0 Note) Wear ring A Special resin Wear ring B Special resin REAR40-PS Piston seal NBR Note) Cushion seal @5 may be difficult to be replaced. Note) Seal kit includes @0 to @5, #0.
For 10 grease pack part no.: GR-F-005 (5 g) for external sliding part GR-S-010 (10 g) for tube interior For 15 grease pack part no.: GR-S-010 (10 g) Piston seal NBR Scraper NBR Cushion seal NBR Seal kit includes @6 to #2.
A spring washer will be required separately for VP470.
Caution The stop position can be changed.
Here, the angular speed can be found from the formula below.
If the tightening torque is exceeded the mounting screws may be broken. IP65 protection cannot be guaranteed if the screws are not tightened to the specified torque. Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it.
1 Be sure to read this before handling the products.