KQ-OMS0022 Air Supply Caution (1)Install an air filter. This may cause leakage or disconnection of the tubing. (10)Avoid installing and using fittings inside a food zone. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5m or finer. (2)Install an aftercooler, air dryer or water droplet separator, etc.
Caution (1) Install an air filter. (4) When connecting the tubing, take pressure or possible changes to the tubing length into account, and allow a sufficient margin. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5m or finer. Failure to do so may result in fitting breakage or detachment of the tubing.
Caution (1) Install an air filter. Install an air filter at the upstream side of valve. Select an air filter with a filtration degree of 5m or finer. (2) Install an aftercooler, air dryer or water separator, etc. Compressed air containing a large amount of drainage can cause the malfunction of pneumatic equipment.
Tightening the threaded portion of an M3, M5 or M6 fittings 1) M3 First, tighten it by hand, then give it an additional 1/4 turn with a wrench. 2) M5 and M6 First, tighten it by hand, then give it an additional 1/6 turn with a wrench. Mounting Caution 1. Check tubing for damage before installing. Confirm model size, etc. 2.
Installation of an air dryer, water separator before filter is recommended. 3. Drain flushing If condensation in the drain bowl of an air filter is not emptied on a regular basis, the condensation will enter the outlet side, causing malfunction of pneumatic devices. If the drain flushing is difficult, installation of a filter with an auto drain option is recommended.
Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of pneumatic systems should be performed by trained and experienced operators. 3. Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1.
Verify the specifications before use. -100 to 0 kPa Setting pressure range -0.1 to 0.45 MPa -0.1 to 0.4 MPa 0.4 (0) MPa (kPa) Air/Non-corrosive non-flammable gas Applicable fluid 0.2 (-50) Setting Pressure Indication light Switch ON: red LED turns on 0 (-100) -0.1 t Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
Connection with tools such as an air driver is also possible. Note) Ensure the TKS does not shake or vibrate. KK Window KK130 Air driver, etc. DM KDM KB 4. Pull the TKS off of the tubing to complete stripping. The tube can be attached as it is to a FR One-touch fitting.
intermediate cylinder position for an extended time If the double check spacer with a built-in double check valve is combined, it will enable the cylinder to stop in the intermediate stroke and maintain its position for a long time without being affected by the leakage between the spools.
intermediate cylinder position for an extended time If the double check spacer with a built-in double check valve is combined, it will enable the cylinder to stop in the intermediate stroke and maintain its position for a long time without being affected by the leakage between the spools.
Theoretica outpul (Nl=Pressure(l\,4Pa) x Pislon area (mm,) able (ks) l,Ore 6rze '. {trim) t"toaet ,1. TYPe d beains 3 tandard s 'qo ' okd ( fYnI ro r r 2.9r 2 3 . 40' I lo , ?
The minimum bending radius indicates the value at a temperature of 20C with an outside diameter rate of change of 10% or less. 3. Please exercise caution when using this item in a clean room.
(mm) 2.5 4 5 6.5 8 KS KX TUS related accessories Inner sleeve TJ Series KM Black (B) White (W) Red (R) Blue (BU) Yellow (Y) Green (G) Translucent (N) Yellow brown (YB) KF M Reinforces soft polyurethane tubing. Insert an inner sleeve into soft polyurethane tubing when used with a One-touch fitting.
Note 2) Mount an inner sleeve when using metal One-touch fittings in high-temperature environments of 60C or more. Use self-align fittings at a temperature of 60C or less. Note 3) The minimum bending radius is the representative value measured as shown in the left figure. Use a tube above the recommended minimum bending radius.
Left end adjustment limit Right end adjustment limit Dimensions Dimensions 30 3000 Applicable One-touch fittings A 25.5 KQ2H/L/T/S/Y06-M5 KQ2H/L07-M5 Other Series KQ2/KS Series KJ 16 16 13 16 AIRCHECKER PS1000-R06L + 13 MADE IN JAPAN G Pressure setting trimmer LED indicator 10 A 30 Revision history Addition of PS1200 (For vacuum) QS Edition B 6 reducer 1/4" reducer SMC Corporation of America