Vacuum Pad In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
when the gripper was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Do not apply a large impact or excessive moment to the slide table (slider). Because the slide table (slider) is supported by a precision bearing, do not apply a large impact or excessive moment when mounting a workpiece. 2. Align carefully when connecting to a load with an external guide mechanism.
Note 6) A reference value for correcting an error in reciprocal operation. Note 7) Impact resistance: No malfunction occurred when the actuator was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.)
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an airhydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5.
Do not use the actuator in an environment where there is possible danger of corrosion. 2. Install a protective cover on the entire product in an environment where a large amount of dust is present or where the product is exposed to water or oil drops. 3. Do not use the actuator in an environment where a strong magnetic field is present. Maintenance Warning 1.
of a command is not normal. 3.12 Negative response HRS400-A-46 3-16 DOC1003626 Chapter 3 Serial communication Communication example Device Address: No.1 Read seven consecutive data from register 0100h which is out of range.
To ensure a permanent path. Stable operation is possible even with an eccentric load, through the use of a ball bushing. When smoother operation is required even with an eccentric load. Auto switches can be mounted. Impact at the stroke end is absorbed by inclusion of a shock absorber. The use of a linear guide makes possible a large load, large moment and high precision.
an intermediate stop of a load using an air pressure circuit, operate at or below the kinetic energy shown in the table below.
Note 1) To protect auto switches, ensure that main body of an auto switch should be embedded into auto switch mounting groove with a depth of 15 mm or more. Note 2) Set the tightening torque of a hexagon socket head set screw (M4) to be 1 to 1.2 Nm. Note 3) When tightening an auto switch mounting screw (M2.5), use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
KQ2LE KQ2TW P.47 P.43 P.46 Use to four-branch a line. Sealant/Gasket Seal Face Seal Gasket Seal Male run tee Tube cap KQ2Y Use to branch a female thread in the same direction and at a 90 angle. KQ2C P.46 P.44 Use to plug unused tubing. The following models do not support oval type release buttons. Refer to the round type (from page 133).
Series KS Blue Series KX Blue Slide bearing Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal.
A water-resistant type cylinder is recommended for use in an environment which requires water resistance.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Since the stroke absorption of rubber bumpers is short, when adjusting the stroke with an A unit, install an external shock absorber.