IO-Link/ELECTRO-PNEUMATIC REGULATOR Minimum pressure (F_1) adjusting range Maximum pressure (F_2) adjusting range 100% 120% 90% 100% 10% 0% 0% 0 50 100 0 50 100 (Note 1): F_1 is adjustable in a range from 0% to 90% of the rated value. (DEFAULT VALUE: 0%) (Note 2): The pressure of less than 0% is not output, even if F_1 is adjusted to less than 0%. (Note 3): F_2 is adjustable in a range from 10 to 120% of the rated value.
JIS B 8361: General rules for hydraulic equipment. JIS B 9960-1: Safety of machinery Electrical equipment for machines. (Part 1: General requirements) < Example of required specifications > JIS B 8433-1993: Manipulating industrial robots Safety. etc. *2) Labor Safety and Sanitation Law, etc.
Specifications Model MGP-Z MGP-AZ Basic type With air cushion Action Double acting Fluid Air Proof pressure 1.5MPa Maximum operating pressure 1.0MPa Minimum operating pressure 12, 16 0.12MPa 16 0.15MPa 20 to 100 0.1MPa 20 to 100 0.12MPa Ambient and fluid temperature -10 to 60 (No freezing 12 to 63 50 to 500mm/s 16 to 63 50 to 500mm/s Piston speed 80, 100 50 to 400mm/s 80, 100 50
Mandrel = LD 2d 1 x 100 Here, : Deformation ratio (%) d: Tube diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Test temperature: 20 5C Relative humidity: 65 5% Air Supply Warning 5.Do not use fluids other than specified. The only fluid that can be used is air. 1. Use clean air.
Here, : Deformation ratio (%) d: Tubing diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Test temperature: 205oC Relative humidity: 655 (%) 100 2d D L 1 = Tube deformation ratio at the minimum bending radius (3) Check the model, type and size before installation.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Maintenance Caution Tube deformation ratio at the minimum bending radius = LD 2d 1 x 100 1.
Tube deformation ratio at the minimum bending radius D L 1 Mandrel 100 2d Here, : Deformation ratio (%) d: Tubing diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Test temperature: 205oC Relative humidity: 655 (%) 4 - (4) Use clean air. 2.
Minimum clearance6mm 100 2d D L 1 = Caution Mandrel (1) Preparation before piping Before piping is connected, the mounting surface of the female thread should be thoroughly cleaned out with air (flushing) or washed to remove chips, cutting oil and other debris from inside the pipe. (2) Check the model, type and size before installation.
Refer to the recommended piping conditions. (4) Do not apply unnecessary forces such as 100 2d D L 1 = Mandrel twisting, pulling, moment loads, vibration and impact, etc. on fittings or tubing. This will cause damage to the fittings and will crush, burst or release tubing. 5 - 2.
D L 1 (2) Winding of sealant tape 100 2d When screwing together pipes and fittings, etc., be Mandrel certain that chips from the pipe threads and sealant do not get inside the pipe. Also, when the sealant tape is used, leave approximately 1 thread ridge exposed at the end of the threads.
Also, when the sealant tape is used, leave approximately 1 thread ridge exposed at the end of the threads. 100 2d D L 1 = Mandrel 5 - 2. Specific Product Precautions (2) (3) Check the model, type and size before installation.
Mounting/ Piping 100 2d D L 1 = Mandrel 5 2. Specific Product Precautions (2) (3) Check the model, type and size before installation. Also, confirm that there are no scratches, gouges or cracks on the product. (4) When connecting the tubing, take pressure or possible changes to the tubing length into account, and allow a sufficient margin.
), VALVE, VQZ2000 VALVE, SOL 4/5-PORT, 2D, VQZ2000 NO SIZE RATING, .14698 lb
), VALVE, VQZ2000 VALVE, SOL 4/5-PORT, 2D, VQZ2000 NO SIZE RATING, .10120 lb
, B/PORT, DIN (DC) *LQA, VALVE, VQZ3000 VALVE, SOL 4/5-PORT, 2D, VQZ3000 NO SIZE RATING, .55629 lb
), VALVE, VQZ2000 VALVE, SOL 4/5-PORT, 2D, VQZ2000 NO SIZE RATING, .12081 lb
, B/MOUNT, IP65 (AC) *LQA, VALVE, VQZ3000 VALVE, SOL 4/5-PORT, 2D, VQZ3000 NO SIZE RATING, .26180 lb
Multiple valve wiring is simplified through the use of the flat ribbon cable connector, Manifold: Single base/B mount, Voltage: 12, 24 VDC; 100, 110 VAC, Clean appearance, VALVE, SGL SOL, BASE MT, VALVE, SYJ3000 SOL VALVE 4/5 PORT, 2D, SYJ3000 NO SIZE RATING, .08157 lb
Magnet: None, Mounting: B (Basic Style), Style: N (Non-lube), Bore Size: 63mm, Port Thread: Rc, Stroke: 100mm, Option: w/o Rod Boot, Cushion: Both Sides, Auto Switch: No Switch, Lead Wire or Prewired Connector: 0.5m (Or None in the Case of No Switch), Number: 2 pcs.
Cylinder (Tube) Inner Diameter(φ): 63, Stroke(mm): 100, Cylinder Operation Method: [Double Acting] Double Acting, Rod Operation Method: Single Rods, Main Body Shape: Standard, Additional Function: Standard, Environment, Applications: Standard, Operating Temperature(°C): -10～50, End Locking: No, Valves: Presence, Operating Pressure(MPa): 0.15～0.9, Cushion: With cushions on both sides, Specification