Mechanically Jointed Rodless Cylinder Series MY2H/HT ø16, ø25, ø40 Grease pack GR-L-005 (5 g) GR-L-010 (10 g) GR-L-150 (150 g) RB Operating Precautions J Warning 1. It might not be able to control CUX10 by meter-out at a low speed operation. DCaution -X 1.
l Center of rotation and center of gravity of the load are concentric. Gravity is applied. mg F l l mg Friction force is applied. Rotation shaft is vertical (up and down). 2 Ta = = t2 Ts = F l Gravity is applied in rotating direction.
Lead Wire Length Lead wire length designation (example) D-A73 L Lead wire length Nil L Z NNote) 0.5m 3m 5m None Note) Applies only to D C type connector switches.
L)-X11 15 B 40 MXS-AT12 (L)-X12 25 C 24.5 MXS-AT16 (L) 5 F K K F MXS16 (L) M5 x 10 M10 x 1 40 23 15 10 14 5 38.5 34.5 MXS-AT16 (L)-X11 15 A J 44.5 MXS-AT16 (L)-X12 25 27.5 MXS-AT20 (L) 5 MXS20 (L) 50 29 21 12 17 6 48 37.5 M12 x 1.25 M5 x 12 MXS-AT20 (L)-X11 15 47.5 MXS-AT20 (L)-X12 25 32.5 MXS-AT25 (L) 5 MXS25 (L) 60 35 23 15 19 6 58 M14 x 1.5 M6 x 16 42.5 MXS-AT25 (L)-X11 15 52.5 MXS-AT25
Port variations Applicable cylinder MY2C16/25/40 MY2H16/25/40 MY2HT16/25/40 R R L L L L L L L L R R R R R R L R Slide table operating direction 40 Series MY2 Auto Switch Precautions 1 Be sure to read before handling. Design and Selection Warning 1. Confirm the specifications.
Grease pack GR-L-005 (5 g) GR-L-010 (10 g) GR-L-150 (150 g) RB Operating Precautions J Warning 1. It might not be able to control CUX10 by meter-out at a low speed operation. DCaution -X 1.
Grease pack GR-L-005 (5 g) GR-L-010 (10 g) GR-L-150 (150 g) RB Operating Precautions J Warning 1. It might not be able to control CUX10 by meter-out at a low speed operation. DCaution -X 1.
How to Order Standard L 40 150 CM2Y L H7BW S 40 150 CDM2Y With auto switch Number of auto switches With auto switch (Built-in magnet) 2 pcs. 1 pc. n pcs.
Size: 30/50/63/80/100 Single shaft with four chamfers: ClRA1BX Double shaft with key: ClRA1BY Double shaft with four chamfers: ClRA1BZ L 0 0.2 L 0 0.2 0 0.1 0 0.1 G G N N H H H U U UU UU M N H L K 0 0.2 G D L 0 0.2 [mm] [mm] [mm] Size G H N U L 30 6 13 8 53 7.8 50 11 27 15 89 14 63 13 29 17 105 16 80 15 38 20 130 19 100 19 44 25 156 24 Size H K UU L 30 25 3 90 14 50 36 5 134 25 63 41 5 158
Enclosure Dustproof ( M8 connector: IP65) Grommet (G)/(H), L plug connector (L), Electrical entry M plug connector (M), M8 connector (W) DC 24, 12, 6, 5, 3 Coil rated voltage (V) 100, 110, 200, 220 AC50/60 Hz Standard Stroke 10% of the rated voltage Allowable voltage Model Standard stroke (mm) 0.35 (With indicator light: 0.4) Standard type DC Power consumption (2) M L 0.1 (With indicator
Dd9 L m MGG (Drill through) 3 x 18 l 4 x 25 l 4 x 35 l 4 x 36 l 0.040 0.076 CD-M03 CD-M05 CD-M08 CDP-7A 10 14 22 25 20, 25 32, 40 50, 63 80 44 60 82 88 3 4 4 4 36 51 72 78 4 4.5 5 5 MGC 0.050 0.093 0.065 0.117 0.065 0.117 l m MGF L Note) Cotter pins and flat washers are included.
Lead wire length (m) Auto switch model Electrical entry direction Perpendicular In-line Indicator light Special function Wiring (Output) Load voltage Applicable load Pre-wired connector 1 (M) Electrical entry Type 0.5 (Nil) 3 (L) 5 (Z) DC AC M9NV M9PV M9BV M9NWV M9PWV M9BWV M9N M9P M9B M9NW M9PW M9BW A96V A93V A90V 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 5 V 12
Vibrations on guide and moving part resistance will result when power over the allowable moment is applied. rFlatness of mounting surface should be less than 0.02mm. l l l allowable load and allowable moment. Refer to p.3.11-10 and 3.11-11 for the details.
of bottom positioning pin hole Position of bottom positioning pin hole Symmetric type For 180 For 90 Positioning pin hole Positioning pin hole 3 Counter-clockwise 3 B port 3 22.5 3 22.5 84 96 e ng e ng ra 3 ra on on ti A port ta 3 ti 90 4 ro ta 7 ro m 1 A port A port u Clockwise m e e m g s u 3 i ni n w im k C ra c l o Mi 6 8 3 ax n o 1 ti M ta ro e m g u m n ni Mi e ra C 180 s l i o