Modular Pressure Control Equipment F.R.L. Replacement Procedure Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.
In case of facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
In case the mounting orientation is not horizontal, a system with a pressure regulating circuit on the lower side is recommended. (It is also effective to shorten start-up delay in rising and for energy conservation.) 12CY1R/3R Caution 1. Pay attention to the cylinder mounting surface.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Size: 3/8, Thread: G, Port Size: 3/8, Accessory: None, Option 1: Drain Cock, Option 2: Flow Direction: Right->Left
Body Size: -, Thread: -, Port Size: -, Mounting: -, Bowl: -, Lubricant Exhaust Port: -, Flow Direction: -, Pressure Unit: -
Body Size: -, Thread: -, Port Size: -, Mounting: -, Bowl: -, Lubricant Exhaust Port: -, Flow Direction: -, Pressure Unit: -
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
W K HT HB HC N X A 2-Plug 4-Counterbore dia.
In case the mounting orientation is not horizontal, a system with a pressure regulating circuit on the lower side is recommended. (It is also effective to shorten start-up delay in rising and for energy conservation.) 12CY1R/3R Caution 1. Pay attention to the cylinder mounting surface.
Min. Dripping Flow Rate(l/min): 40, Oil Storage Capacity(cm3): 135, Case: [Resin] Polycarbonate Case, Inlet Side Connection Type: Rc, Inlet Side Plumbing Thread Nominal: 3/8, Outlet Side Connection Type: Rc, Outlet Side Plumbing Thread Nominal: 3/8, Drain Exhaust: [Manual] With Drain Cock, Flow Direction: [Left] From Right to Left, Size of Body: 40, Accessory: Without optional
Body Size: 40, Thread: Rc (Rc: for Sizes 20~60; M5: for Size 10), Port Size: 03 (3/8), Mounting: None, Semi-Standard, Body Size 10: 3 (Drain Cock), Semi-Standard, Body Size 20: R (Flow Direction: Right to Left), Semi-Standard, Body Size 30, 40, 50 & 60: Standard