The cylinder section does not have a water resistant enclosure. 3-3 Allowable Kinetic Energy 3-3-1 Allowable Kinetic Energy (J) Bore size(mm) 12 20 32 40 50 63 Allowable Kinetic EnergyE 0.022 0.055 0.15 0.26 0.46 0.77 3-3-2 Mass of Cylinder Movable Parts (g) Cylinder stroke (mm) Bore size(mm) 25 50 75 100 125 150 175 200 250 300 400 500 12 28 33 38 43 48 53 20 70 84 98 112 126 140 154 168
Heavy load Standard load Medium load Light load 1 10 50 100 200 1 0.25 0.49 0.98 1.96 2 20 2 0.49 75 200 400 0.74 1.47 2.94 3 30 3 0.74 100 300 600 0.98 1.96 3.92 4 40 125 400 800 4 0.98 1.23 2.45 4.90 5 50 5 1.23 150 500 1000 1.47 2.94 5.88 6 75 200 600 1200 6 1.47 1.96 3.92 7.84 7 100 250 700 1400 7 1.72 2.45 4.90 9.80 8 300 300 800 1600 8 1.96 2.94 5.88 11.76 9 500 500 900 1800 9 2.21
Tightening torque Nominal 1.40.1Nm 125 or 150 10. Mount the bowl assembly. AL20-A Referential tightening torque Hold the bowl assembly by hand and rotate clockwise. Do not use tool for mounting because the bowl may be damaged. See check item for referential tightening torque. 2.1 Nm Disassembly 1. Remove the bowl assembly.
Wiring diagram (Power supply and monitor output) Switch output NPN type Switch output PNP type ITV 0 0-52 ITV 0 0-53 When a current of approx.150 mA or more is applied, the over current circuit will operate, Er.5 will be displayed and the operation will stop.
The graphs below show the variation of the distance for the product to turn ON, for 3 types of gap, by changing the supply pressure (50 kPa) when the product is set to turn ON at 150 kPa supply pressure. Detection nozzle: 1.5 Piping: F type: 4 x 2.5 tube Test conditions G, H type: 6 x 4 tube Reference pressure: 150 kPa : Use within the rated pressure range (100 kPa to 200 kPa).
(between FE and all accessible terminals) Insulation resistance 10 M ohm or more (500 VDC is given between FE and all accessible terminals) Ambient temperature Operation: -10 C to 50 C Storage: -20 C to 60 C Ambient humidity 35% to 85% RH (non-condensing) 10 Hz to 57 Hz (constant amplitude) 0.75 mm 57 Hz to 150 Hz (constant acceleration) 49 m/s2 2 hours for each direction X, Y and Z (complies
Performance Performance data shown in this chapter is based on an electrified plate (dimensions: 150 x 150 mm, electrostatic capacity: 20pF) defined by ANSI standard (ANSI/ESD STM3.1-2006). Use this data as a guideline for selection, as the performance data may vary depending on the material and size of the work piece. 5 -1.
Round cutting pliers Nominal: 125 or 150 Tightening torque: 1.4 0.1 Nm 10) Mount the bowl assembly. Hold the bowl assembly by hand and rotate clockwise. Do not use tool for mounting because the bowl may be damaged. Refer to the Check item for referential tightening torque. Actuators Modular F.R.L.
150 130 120 50 50 MSZA30A (High precision type) MSZA50A(High precision type) D70 60 50 40 30 20 10 0 120 100 80 60 40 20 0 Load N Load N 291 Rotary Table Air Consumption Air consumption is the volume of air which is expended by the rotary tables reciprocal operation inside the actuator and in the piping between the actuator and the switching valve, etc.
Note 1) Note 2) Maximum available stroke (mm) Bore size (mm) 20 25 32 40 Standard stroke (mm) Model Long stroke (mm) 1 pc. 201 to 350 301 to 400 301 to 450 301 to 800 25, 50, 75, 100, 125, 150, 200 D-C7, C8 D-B5, B6 D-H7 D-G5N 15mm 10mm 1500 25, 50, 75, 100, 125, 150, 200, 250, 300 20mm 20mm 15mm 10mm D-B59W D-H7LF Note 1) Intermediate strokes other than the above are produced upon receipt
Standard Stroke (mm) Manufacturable stroke range Model Standard strokes CXSJ6 CXSJ10 CXSJ15 CXSJ20, 25, 32 60 to 100 10, 20, 30, 40, 50 80 to 150 10, 20, 30, 40, 50, 75 110 to 150 10, 20, 30, 40, 50, 75, 100 110 to 200 Strokes beyond the standard stroke range are available as a special order.
Without motor brake Without motor brake With motor brake With motor brake Without motor brake 50 Direct acting guide Series LXF 0.03 Ball screw 3 100 50 Series LXP 6 Ball bushing guide 100 Ball screw 0.03 50 5 100 Series LXS 50 10 High rigidity direct acting guide 100 Ball screw 0.03 50 5 100 5 Simplified Selection Flow Chart Series LX Standard stroke (mm) and 25 50 75 100 125 150
OFF SUP 1MC 5Ry SGDE servomotor Motor 1MC 1 R U V SGDE servo pack 2 1MC M T 3 W 1CN 4 150 PULS PULS SIGN SIGN CLR CLR 1 2 3 4 5 6 Be sure to ground.
A 1 2 150 165 42.7 76.3 45 65 40 60 35 40 80 80 ALBA90-10 ALBA90-20 1.17-24
removal rate blowing compressor is 30mg/m3(ANR) (ANR) Accessories (Options) Applicable models AM150 AM250 AM350 AM450 AM550 AM650 AM850 Bracket assembly With cap bolt, BM51 BM52 BM53 BM54 BM55 BM56 BM57 spring washer Symbol AM Order Made P.4.6-6 How to Order AM 250 03 J B Options Body size Accessories (Options) Drain guide 1/4B female thread INOUT reversal Element service indicator None 150
BM51 BM52 BM53 BM54 BM55 BM56 BM57 How to Order AME 250 03 R B Option R INOUT reversal Body size HAl Accessories (Options) 150 250 350 450 550 650 850 1/8 1/4 3/8 1/2 3/4 None B AT With bracket IDl Port size 1/8B 01 02 03 04 06 10 14 20 2B 1 Thread 1/4B AMG 11/2 3/8B Rc(PT) F G(PF) N NPT 1/2B AFF 3/4B 1B AMl 11/2B Symbol Related poroducts AME Note) Refer to p.4.7-7 for "How to Order" case
assembly With cap bolt With spring washer BM51 BM52 BM53 BM54 BM55 BM56 BM57 Condition of inlet air Pressure: 0.7MPa Temperature: 25C Relative humidity: 100% How to Order AMG 250 03 J B Liquid water content (Water droplet content): 1.5g/m3 (ANR) Options Body size Compressed air flow: Rated flow of each model J Drain guide 1/4B female thread R IN-OUT reverse direction 1/8 1/4 3/8 1/2 3/4 1 150
Symbol Order Made P.4.6-21 4.6-15 Micro Mist Separator with Prefilter Series AMH AMH150 to AMH850 How to Order AMH 250 03 J B Body size Options J Drain guide 1/4B female thread R IN/OUT reversal 150 1 8 250 1 4 350 3 8 450 1 2 550 3 4 650 1 850 11 2 Accessories(Options) Description None Bracket Symbol T Element service indicator B N.C.auto drain C N.O.auto drain D Note) Refer to p.4.7-7
Flow rate l/min (ANR) Relief flow rate l/min (ANR) Supply pressure P1 MPa IR1010-01 IR1010-01 IR1010-01 Conditions: Supply pressure 0.7MPa Conditions: Back pressure 0.7MPa 0.4 0.204 0.7 Set pressure P2 MPa 0.6 Set pressure MPa Set pressure MPa 0.202 0.3 0.5 Setting point 0.4 0.200 0.2 0.3 0.198 0.2 0.1 0.1 0.196 0 0.2 0.1 0.3 0.4 0.6 0.5 0.8 0.7 0.9 0 50 100 150 200 250 300 350 1.0 0 40
with no freezing) Ambient and fluid temperature With auto switch 10 to 60C (14 to 140F) (with no freezing) Non-lube Lubrication 50 to 700mm/s (2 to 27.5in/s) Piston speed +1.4 0 +1.0 0 Stroke length tolerance to 250 , 251 to 1000 mm Rubber bumper Cushion JIS class 2 Thread tolerance 1/4 1/4 1/4 Port size Standard strokes Bore size (mm) Standard strokes (mm) Long strokes (mm) 75, 100, 125, 150