Lateral Load Resisting Low Friction Cylinder Series MQM ø6, ø10, ø16, ø20, ø25 size (mm) MM A NN D F G1 G2 S ZZ I H J N1 N2 NA TN TF 10 15 M12 x 1 4 M5 x 0.8 8 15 6 M4 x 0.7 65 101 18.5 28 16 11 20 16 16 15 M14 x 1 5 M5 x 0.8 10 15 6 M5 x 0.8 74 114 22 30 22 12 21 19.5 20 18 M20 x 1.5 8 Rc1/8 13 NPT1/8 25 G1/8 8.5 M8 x 1.25 97.5 151 31.5 40.5 28.5 20.5 33 29 25 M10 x 1.25 18 M26 x 1.5 10 Rc1/8 13 NPT1/8 30 G1/8 8.5 102.5 160 34.5 44.5 32 20.5 38 32 Refer to page
l/8 a a a a a 3/8 a a a 1/2 a 3t4 a a a a Note 2) For M5 and NPT thread lypes Accessories Wrlh o?
(RES) A.10 Undervoltage A.12 Memory error 1 (RAM) A.13 Clock error A.15 Memory error 2 (EEP-ROM) A.16 Encoder initial communication error1 A.17 Board error A.19 Memory error 3 (Flash-ROM) A.1A Motor combination error A.1C Software combination error A.1E Encoder initial communication error 2 A.1F Encoder initial communication error 3 A.20 Encoder normal communication error 1 A.21 Encoder normal
Just like a relay, these devices open or close a mechanical contact with the power of a solenoid. The principle of operation is the same as a relay, but a contactor is designed for high-voltage and large current. RS232C A standard for serial communication.
GC SB + Stroke B ZZ + Stroke A + Stroke B SA + Stroke A 63 SZ + Stroke B Front mounting flange C port A, B port B port A 20 C port A port A ' View A-A' GC SB + Stroke B ZZ + Stroke A + Stroke B SA + Stroke A 41 Made to Order Specifications Series MGG Auto Switch Rail Mounting 8 MGG XC13 Bearing type Mounting type Stroke Auto switch type Auto switch symbol Bore size Auto switch rail mounting
A C B A C B Stroke A operation 1) Initial state (0 stroke position) 1) Initial state (0 stroke position) Stroke B Stroke A Stroke B Stroke A A A 2) 1st stage: Stroke A operation When the air pressure is supplied from the A port, the rod operates the stroke A. 2) Operation When the air pressure is supplied from the A port, the rod operates the stroke A.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
M5 (PV, PD port): After tightening by hand, increase the tightening by about 1/6 turn with a tightening tool. Tightening torque is 1 to 1.5N as a guide. (3) When mounting or removing the tube fitting, etc. to the manifold base, hold the manifold base hold the manifold base with a spanner.
During Auto tuning Auto tuning failure A T 1 E R R 1 9 P V < 2 3 . 0 C # 1 A T F a i l u r e A u t o T u n i n g M O D E S h u t O f f C a n c e l : A T k e y <4> External sensor sampling cycle setting: Mode indication External Sensor Sampling Cycle. Default value: 180 sec. Setting range 10 to 999 sec.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
In an environment where the product will come into direct contact with rain, wind and snow or with a lot of moisture (relative humidity 85% or more). (Note) In a location with a large quantity of dust. In a location containing flammable or explosive gases. In a location exposed to corrosive or flammable gases or solvent.
Clip Type 45 manifold permits change in the A and B port sizes by changing the manifold block fitting assembly. After removing the valve, remove the clip with a screwdriver. To mount a new fitting assembly insert it and then insert a clip so it does not come out of the manifold block. Loosen bolt (a) fixing the manifold base until it begins to turn idly.
From a point indicating 500 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the 63 mm bore size. Extend a line from the intersection to the left and find a load mass 80 kg.
Ventilation Provide ventilation when using a valve in a confined area, such as in a closed control panel.
Clip Type 45 manifold permits change in the A and B port sizes by changing the manifold block fitting assembly. After removing the valve, remove the clip with a screwdriver. To mount a new fitting assembly insert it and then insert a clip so it does not come out of the manifold block. Loosen bolt (a) fixing the manifold base until it begins to turn idly.
In an environment where the product will come into direct contact with rain, wind and snow or with a lot of moisture (relative humidity 85% or more). (Note) The option B is provided for installation under a roof, but should not be used in environments where rain or snow may fall on it. In a location with a large quantity of dust. In a location containing flammable or explosive gases.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.